077 901 xerox ошибка 3045

077-104, 109, 113, 901 Fuser Exit Sensor Jam RAP

BSD-ON: BSD 10.3 Fusing

077-104 The trail edge of the paper deactuated the fuser exit sensor earlier than the specified time.
077-109 The fuser exit sensor did not actuate within the specified time after the registration clutch energized.
077-113 The trail edge of the paper deactuated the fuser exit sensor later than the specified time.
077-901 The fuser exit sensor detected remaining paper.

Initial Actions

• Check the condition of the paper in all trays. Refer to GP 15 Paper and Media Size Specifications
• Ensure that the fuser is installed correctly.

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

WARNING: Do not touch the fuser while it is hot.

Refer to the procedures that follow as necessary:

• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.

Perform the steps that follow:

1. Check for obstructions in the paper path.
2. Check the exit 2 roll and nip rolls, PL 10.22 for foreign substances or wear. Clean or install new components as necessary.
3. Remove the fuser. Check whether foreign substances or paper is wound around the heat roll.
4. Enter dC330, code 077-101. Check the fuser exit sensor, part of the fuser, PL 10.05 Item 2.
5. Enter dC330, code 042-003. Check the main motor, PL 40.10 Item 10.
6. Enter dC330, code 077-014. Check the exit 2 motor, PL 10.21 Item 4.
7. Enter dC330, code 077-002. Check the registration clutch, PL 80.55 Item 11.
8. Check the exit 2 drive gears, PL 10.21 for wear or damage.
9. Check the registration transport assembly, PL 80.55 Item 1 for wear or damage.
10. If the fault persists, install new components as necessary:

• Drive PWB, PL 1.10 Item 4.
• ESS PWB, PL 3.10 Item 6.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

• 106R03733 106R03736 106R03735 106R03734

Drum Chip:

• 113R00780 113R00782

Модератор: vetal

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 53

пишет,что застряла бумага,а на самом деле этого нет

23.10.2013

Вопрос:

В мфу Work centre 3045 высвечивается ошибка застревание бумаги на рег.077-901 — принтер,а на самом деле застрявшей бумаги не видно.Что делать?

Ответ:

Скорее всего, проблема в датчиках. Обратитесь в сервисный центр.

Задайте свой вопрос