C0630 kyocera код ошибки - Не ошибается лишь тот, кто ничего не делает!

Andreyak777 » Пт фев 01, 2013 4:03 am

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Lynx » Пт фев 01, 2013 9:52 am

kvg писал(а):Мануал в личке.

спасибо огроменное за мануал. Нашла в нем эту ошибку, а не подскажете еще, что именно в мануале обозначают аббревиатурой PWB — весь мануал изрыла — никак не пойму.Только куча соотношений с ней, например PDPWB и т.п.

Lynx

Починил струйный принтер

Персональный альбом

Lynx » Пн фев 04, 2013 12:50 pm

kvg писал(а):Это означает главную плату, типа материнской в компьютере. В общем легче копир целиком купить, чем ее менять думаю.

Ага, но копир хоть и ругается, пока еще работает. Как думаете — долго проживет?

Lynx

Починил струйный принтер

Персональный альбом

Lynx » Пн фев 04, 2013 1:20 pm

Написано: Replace the main PWB and check for correct operation.
т.е. как я перевела именно главная плата.

Интересно, сколько она стоит и сколько работы по ее замене…

Lynx

Починил струйный принтер

Персональный альбом

[SCANNER ERROR] Lamp Error Kyocera FS-1016

мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

3

6641

Усатый Полосатый

Вс окт 28, 2018 11:08 pm
Kyocera 1035 «бледная» печать

srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

2

13946

srMax

Пт янв 23, 2015 2:49 pm
Kyocera FS-1120d индикатор «Нет бумаги»

vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

11

15137

СТРОНЦИЙ

Вт ноя 02, 2021 2:24 pm
Kyocera Ecosys M2635dn «поворот» изображения

Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

10

6098

MatrixAgent

Ср апр 08, 2020 5:18 am
Стирание вала ведущей шестерни в «печке» Kyocera M2035dn

Грецкий орех в форуме Принтеры, МФУ, факсы, копиры формата A4

12

3458

СТРОНЦИЙ

Пн дек 13, 2021 3:35 pm

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 15

Источник

Оборудование оснащено функцией самодиагностики. При обнаружении проблемы, аппарат блокируется, на дисплее отображается код вида С#### с указанием характера проблемы. Также появляется сообщение необходимости обслуживания. После устранения проблемы, ошибку можно сбросить тумблером питания, выключив и включив аппарат.

При обнаружении неисправности дополнительного устройства (ошибки C8170, C8180, C8190, C8210)* производится частичная блокировка функциональности аппарата. После устранения неисправности ошибку можно сбросить в сервисном режиме U906.

Ошибки узла закрепления изображения (печные ошибки) C6###, после устранения неисправности и в целях безопасности, сбрасываются только в сервисном режиме U163.

Таблица кодов ошибок:

Код	Значение	Описание	Причина	Решение

C0100	Backup memory (EEPROM) device problem (main)	Reading from or writing to EEPROM cannot be performed.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C0110	Backup memory data problem (main)	Data in the specified area of the backup memory does not match the specified values.	Data damage of EEPROM.	Contact the Service Administrative Division.
C0150	Backup memory device problem (engine EEPROM)	Reading from or writing to EEPROM cannot be performed.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
			Device damage of EEPROM.	Contact the Service Administrative Division.
C0160	Backup memory data problem (engine EEPROM)	Reading data from EEPROM is abnormal.	Data damage of EEPROM.	Contact the Service Administrative Division.
C0170	Copy counts problem	When the power is turned on, the total count and the scan count are abnormal both on the main and engine.	Data damage of EEPROM.	Contact the Service Administrative Division.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C0180	Machine number mismatch	Machine number of main and engine does not match.	Data damage of EEPROM.	Contact the Service Administrative Division.
C0210	Communication problem between the main and engine	When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for 10 s.	Poor contact in the connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C0240	Printer PWB communication problem	The printer PWB does not respond 120 s after the power is turned on.	Poor contact in the connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
A0410	Document processor communication problem	Communication fails five times successively.	Document processor installed incorrectly.	Check the installation state of the document processor and adjust it if it is not properly installed.
			Defective PWB.	Replace the main/engine PWB or DP driver PWB and check for correct operation.
A0420	First paper feeder communication problem	Communication fails five times successively.	First paper feeder installed incorrectly.	Check the installation state of the first paper feeder and adjust it if it is not properly installed.
			Defective PWB.	Replace the main/engine PWB or cassette main PWB and check for correct operation.
C0440*	Built-in finisher communication problem	Communication fails five times successively.	Poor contact in the connector terminals.	Check the connection of connector YC4 on the engine PWB and the connector of the built-in finisher, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective PWB.	Replace the engine PWB or finisher main PWB and check for correct operation.
A0500	Second paper feeder communication problem	Communication fails five times successively.	Second paper feeder installed incorrectly.	Check the installation state of the second paper feeder and adjust it if it is not properly installed.
			Defective PWB.	Replace the main/engine PWB or cassette main PWB and check for correct operation.
A0510	Third paper feeder communication problem	Communication fails five times successively.	Third paper feeder installed incorrectly.	Check the installation state of the third paper feeder and adjust it if it is not properly installed.
			Defective PWB.	Replace the main/engine PWB or cassette main PWB and check for correct operation.
C0610	Bitmap (DIMM) problem	There is a problem with the data or address bus of the bitmap DRAM.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
			DIMM installed incorrectly.	Check if the DIMM is inserted into the socket on the main/engine PWB correctly.
			Defective DIMM.	Replace the DIMM and check for correct operation.
C0620	Memory input interface problem	Reading-in of an image does not complete within 10 s of the start of image transmission.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C0630	DMA problem	DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C0800	Image processing problem	JAM05 is detected twice.	Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C2000	Drive motor problem	A stable state does not continue for 1 s from 1 s after the drive motor is activated.	Poor contact in the connector terminals.	Check the connection of connector YC6 on the main/engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective drive transmission system.	Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
			Defective drive motor.	Replace the drive motor.
C2200	Drum motor problem	A stable state does not continue for 1 s from 1 s after the drum motor is activated.	Poor contact in the connector terminals.	Check the connection of connector YC6 on the main/engine PWB and the connector on the drum motor, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective drive transmission system.	Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
			Defective drum motor.	Replace the drum motor.
C3100	Scanner carriage problem	The home position is not correct when the power is turned on or at the start of copying using the table.	Poor contact in the connector terminals.	Check the connection of connector YC5 on the main/engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective home position switch.	Replace the home position switch.
			Defective scanner motor.	Replace the scanner motor.
			The mirror frame, exposure lamp, or scanner wire is defective.	Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C3200	Exposure lamp problem	Non-lighting of the exposure lamp is detected at the beginning of copying.	Poor contact in the connector terminals.	Check the connection of connector YC16 on the main/engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective exposure lamp.	Replace the exposure lamp.
			Incorrect shading position.	Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch.
			Defective PWB.	Replace the main/engine PWB or inverter PWB and check for correct operation.
C3300	AGC problem	After AGC, correct input is not obtained at CCD.	Poor contact in the connector terminals.	Check the connection of connector YC27 on the main/engine PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective exposure lamp.	Replace the exposure lamp.
			Defective PWB.	Replace the main/engine PWB or CCD PWB and check for correct operation.
C4000	Polygon motor synchronization problem	The polygon motor does not reach the stable speed within 20 s of the START signal turning on.	Poor contact in the connector terminals.	Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective polygon motor.	Replace the laser scanner unit.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C4010	Polygon motor steady-state problem	Stable OFF is detected for 5 s continuously after polygon motor stability.	Poor contact in the connector terminals.	Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective polygon motor.	Replace the laser scanner unit.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C4200	BD steady-state problem	ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.	Poor contact in the connector terminals.	Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
			Defective laser scanner unit.	Replace the laser scanner unit.
			Defective main/engine PWB.	Replace the main/engine PWB and check for correct operation.
C6000	Fuser heater break	The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization. Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).	Poor contact in the fuser thermistor connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Fuser thermistor installed incorrectly.	Check and reinstall if necessary.
			Fuser thermostat triggered.	Check for continuity. If none, replace the fuser thermostat.
			Fuser heater installed incorrectly.	Check and reinstall if necessary.
			Broken fuser heater wire.	Check for continuity. If none, replace the fuser heater.
C6020	Abnormally high fuser thermistor temperature	Fuser thermistor is detected 230°C/ 446°F or more for 40 ms.	Shorted thermistor.	Measure the resistance. If it is 0 Ω, replace the thermistor.
			Broken heater control circuit on the power source PWB.	Replace the power source PWB and check for correct operation.
C6050	Abnormally low fuser thermistor temperature	Fuser thermistor remains below 90°C/ 194°F for 1 s.	Poor contact in the fuser thermistor connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Broken fuser thermistor wire.	Measure the resistance. If it is ∞ Ω, replace the fixing thermistor.
			Fuser thermistor installed incorrectly.	Check and reinstall if necessary.
			Fuser thermostat triggered.	Check for continuity. If none, replace the fuser thermostat.
			Fuser heater installed incorrectly.	Check and reinstall if necessary.
			Broken fuser heater wire.	Check for continuity. If none, replace the fuser heater.
C6400	Zero-cross signal error	Interrupt of the zero-cross signal does not occur more than 1 s.	Poor contact in the connector terminals.	Reinsert the connector. Also check for conti- nuity within the connector cable. If none, remedy or replace the cable.
			Defective power source PWB.	Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB.
			Defective main/engine PWB.	Replace the main/engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal.
C7800	Broken external thermistor wire	The thermistor output value is 0.5 V or less.	Poor contact in the connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective humidity sensor.	Replace the cassette PWB and check for correct operation.
C7810	Short-circuited external thermistor wire	The thermistor output value is 4.5 V or more.	Poor contact in the connector terminals.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective humidity sensor.	Replace the cassette PWB and check for correct operation.
C8170*	Built-in finisher front side registration motor problem	When the front-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the front-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s.	The front side registration motor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective front side registration motor.	Replace front side registration motor.
			The front side registration home position sensor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective front side registration home position sensor.	Replace the front side registration home position sensor.
			Defective finisher control PWB.	Replace the finisher control PWB and check for correct operation.
C8180*	Built-in finisher rear side registration motor problem	When the rear-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the rear-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s.	The rear side registration motor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective rear side registration motor.	Replace rear side registration motor.
			The rear side registration home position sensor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective rear side registration home position sensor.	Replace the rear side registration home position sensor.
			Defective finisher control PWB.	Replace the finisher control PWB and check for correct operation.
C8190*	Built-in finisher trailing edge registration motor problem	When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s.	The trailing edge registration motor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective trailing edge registration motor.	Replace trailing edge registration motor.
			The trailing edge registration home position sensor connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			Defective trailing edge registration home position sensor.	Replace the trailing edge registration home position sensor.
			Defective finisher control PWB.	Replace the finisher control PWB and check for correct operation.
C8210*	Built-in finisher stapler problem	The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation. During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation.	The stapler connector makes poor contact.	Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
			The stapler is blocked with a staple.	Remove the stapler cartridge, and check the cartridge and the stapling section of the stapler.
			The stapler is broken.	Replace the front stapler and check for correct operation.
			Defective finisher control PWB.	Replace the finisher control PWB and check for correct operation.

*) Kyocera TASKalfa 181/221

Источник

06-27-2011

#1

Technician

Rep Power

27

Hi friends,
in kyocera mita km2530 i found error c630 while taking a back to back copies, in single side nothing its comes what i need to do help me please.

thenks
06-27-2011

#2

C0630 = DMA problem
• DMA transmission of compressed,
decompressed, rotated, relocated or
blanked-out image data does not
complete within the specified period
of time.

Solution: Replace the main PCB and check for correct operation.

I would suggest to go to maintenance mode and do U906 reset. It should clear if not than , check also Memory module, if you can swap it from another machine.
06-28-2011

#3

Technician

Rep Power

27

thanks guy i try it this.
07-02-2011

#4

Re: c0630

Originally Posted by habik

C0630 = DMA problem
• DMA transmission of compressed,
decompressed, rotated, relocated or
blanked-out image data does not
complete within the specified period
of time.

Solution: Replace the main PCB and check for correct operation.

I would suggest to go to maintenance mode and do U906 reset. It should clear if not than , check also Memory module, if you can swap it from another machine.

I have come across this code on numerous occasions, The cable from the Document feeder to the rear of the machine should be checked to ensure proper connection, Just recently we had a Utax cdc1725 / 250cii with DF650(B) showing this code, after printing out the event log the machine had totalled 15 c0630 codes. I checked the service manual and and inspected the cable, The connector to the machine had been damaged. After investigating the cause, it was discovered that the customer had been moving the machine from one end of the site to the other by pulling the cable ???

Hope this helps

Источник

Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки	Описание ошибки	Причина ошибки
0030	FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.	Defective FAX control PWB.
0060	Engine PWB type error	Defective engine sub PCB.
0070	FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.	Defective FAX software Defective FAX control PWB.
0100	Backup memory device error	Defective flash memory.
0120	MAC address data error For data in which the MAC address is invalid.	Defective main PWB. Defective flash memory. Defective engine PWB.
0130	Backup memory read/write error (main PWB)	Defective flash memory. Defective main PWB.
0140	Backup memory data error (main PWB)	Defective flash memory. Defective main PWB.
0150	Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error.	Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM.
0160	Backup memory data error (engine PWB)	Defective flash memory. Defective engine PWB.
0170	Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.	Data damage of EEPROM. Defective PWB.
0180	Machine number mismatch Machine number of main and engine does not match.	Data damage of EEPROM.
0320	I/O CPU communication error A communication error is detected 10 times in succession.	Defective PWB.
0630	DMA error DMA transmission of image data does not complete within the specified period of time.	Poor contact in the connector terminals. Defective main PWB.
0800	Image processing error JAM05 is detected twice.	Defective main PWB.
0830	FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.	Defective FAX software. Defective FAX control PWB.
0840	Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	The battery is disconnected from the main PWB. Defective main PWB.
0870	FAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times.	Improper installation FAX control PWB. Defective FAX control PWB or main PWB.
0920	Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.	Defective FAX control PWB.
1010	Lift motor error After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB.
1020	PF lift motor error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 1. Defective PF lift motor 1. Defective PF main PWB.
1030	PF lift motor error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 2. Defective PF lift motor 2. Defective PF main PWB.
1800	Paper feeder communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.
1900	Paper feeder EEPROM error When writing the data, the write data and the read data is not continuously in agreement 5 times.	Defective PF main PWB. Device damage of EEPROM.
2000	Main motor steady-state error Stable OFF is detected for 1 s continuously after main motor stabilized.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2010	Main motor drive error The main motor is not stabilized within 2 s after driving starts.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2600	PF drive motor error (paper feeder) When the PF drive motor is driven, error signal is detected continuously for 1 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
3100	ISU home position error The home position is not correct when the power is turned on or at the start of copying using the table.	Defective connector cable or poor contact in the connector. Defective home position sensor. Defective ISU motor. Defective CCD PWB. Defective engine PWB.
3200	Exposure lamp error When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s.	Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective CCD PWB. Defective main PWB.
3500	Communication error between scanner and ASIC An error code is detected 3 times in succession.	Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB.
3600	Scanner sequence error	Defective main PWB or engine PWB.
4000	Polygon motor synchronization error The polygon motor is not stabilized within 10 s after driving starts.	Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB.
4010	Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized.	Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB.
4100	BD initialization error BD is not detected within 1 s after polygon motor stabilized.	Defective connector cable or poor contact in the connector. Defective APC PWB. Defective BD PWB. Defective main PWB.
4700	VIDEO ASIC device error	Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB.
6000	Broken fuser heater wire The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.
6000 6020 6030 6050	Broken fuser heater wire Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature	Deformed connector pin. Defective triac.
6020	Abnormally high fuser thermistor temperature The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms.	Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.
6030	Broken fuser thermistor wire A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Defective fuser thermistor. Defective engine PWB
6050	Abnormally low fuser thermistor temperature As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second.	Deformed connector pin. Defective triac. Defective fuser thermistor Defective fuser heater. Defective engine PWB.
6400	Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 3 s.	Defective connector cable or poor contact in the connector Defective power source PWB or engine PWB.
7800	Broken external thermistor wire The thermistor output value is 0.3 V or less.	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7810	Short-circuited external thermistor wire The thermistor output value is 3 V or more.	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7900	Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.	Defective connector cable or poor contact in the connector. Defective drum unit.
7910	Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.	Defective connector cable or poor contact in the connector. Defective developer unit.
8030	Tray upper limit detection problem (document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected.	Defective connector cable or poor contact in the connector. Defective tray upper limit sensor, paper surface sensor 1/2. Defective DF main PWB.
8040	Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on.	Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB.
8140	Tray elevation motor problem (document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated.	Defective connector cable or poor contact in the connector. Defective connector cable or poor contact in the connector. The tray elevation motor malfunctions. Defective tray lower limit sensor, paper surface sensor 1/2. Defective DF main PWB.
8210	Stapler problem (document finisher) Jam 7012 or 7023 is indicated.	Defective connector cable of staple or poor contact in the connector. The stapler is blocked with a staple. The stapler is broken Defective DF main PWB.
8320	Adjustment motor 2 problem (document finisher) The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on.	Defective connector cable or poor contact in the connector. Defective adjustment sensor 2. Defective adjustment motor 2. Defective DF main PWB.
8330	Adjustment motor 1 problem (document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on.	Defective connector cable or poor contact in the connector. Defective adjustment sensor 1. Defective adjustment motor 1.
8350	Roller motor problem (document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on.	Defective DF main PWB. Defective connector cable or poor contact in the connector. Defective roller sensor. Defective roller motor. Defective DF main PWB.
8360	Slide motor problem (document finisher) The slide sensor does not turn on/off within specified time of the slide motor turning on.	Defective connector cable or poor contact in the connector. Defective slide sensor. Defective slide motor. Defective DF main PWB.
8460	EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed.	Defective EEPROM or DF main PWB.
8800	Document finisher communication error A communication error is detected 10 times in succession.	Defective connector cable or poor contact in the connector Defective DF main PWB. Defective engine PWB.
8830	Bridge communication error (document finisher) A communication error is detected 10 times in succession.	Defective connector cable or poor contact in the connector. Defective bridge PWB. Defective engine PWB.
8990	Document finisher communication error	Defective connector cable or poor contact in the connector. Defective DF main PWB. Defective bridge PWB.
9000	Document processor communication error A communication error is detected 10 times in succession.	Defective connector cable or poor contact in the connector. Defective DP main PWB.
9060	DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.	Defective DP main PWB. Device damage of EEPROM.
9500	BRU communication error	IPU PWB error
9510	BRU PWB error	IPU PWB error
9520	BRU PWB data error	IPU PWB error
F000	Main PWB — operation panel PWB communication error	Defective main PWB. Defective operation panel PWB.
F010	Main PWB checksum error	Defective main PWB.
F040	Main PWB — print engine communication error	Defective main PWB. Defective engine PWB.
F050	Print engine ROM checksum error	Defective engine PWB.

Источник

Code: 0030
Description: FAX control PWB system error
Processing with the fax software was disabled due to a software problem.
Causes: FAX control PWB
Remedy: 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB.

Code: 0060
Description: Main/Engine PWB mismatch
Unmatching engine and engine sub boards. Defective engine subboard
Causes: Main/Engine PWB
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the main/engine PWB.

Code: 0100
Description: Backup memory device error
Causes: EEPROM (Main/Engine PWB)
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main/engine PWB.

Code: 0120
Description: MAC address data error
For data in which the MAC address is invalid.
Causes: EEPROM (Main/Engine PWB)
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check the MAC address on the network status page. 3. If it is blank, obtain an EEPROM with its MAC address written from the service support and install. 4. Replace the main/engine PWB.

Code: 0150
Description: Backup memory read/write error (main/engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
Causes: EEPROM (Main/Engine PWB)
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM is peroperly installed on the main/engine PWB and re-install it. 3. Replace the main/engine PWB. 4. Check the EEPROM and if the data are currupted, contact the service support.

Code: 0160
Description: Backup memory data error (main/engine PWB)
Reading data from EEPROM is abnormal.
Causes: EEPROM
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Execute U021 — memory initializing.(see page 1-3-19) 3. If the EEPROM data are currupted, contact the service support.

Code: 0170
Description: Billing counting error
The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter.
Causes: EEPROM. Main/Engine PWB.
Remedy: EEPROM 1. Check that the EEPROMs installed in the main/engine PWB are correct and, if not, use the correct EEPROM for the model. 2. If the EEPROM data are currupted, contact the service support.
Main/Engine PWB Replace the main/engine PWB.

Code: 0180
Description: Machine number mismatch
Machine number of main/ engine does not match.
Causes: Data damage of EEPROM.
Remedy: 1. Confirm the machine data for the main/ engine units by using U004. 2. If the serial number data of different models is alternately displayed, install the correct EEPROM in the PWB of the wrong serial number data. 3. Contact the Service Support.

Code: 0190
Description: Backup memory device error (main/engine PWB)
Causes: Main/Engine PWB
Remedy: Replace the main/engine PWB.

Code: 0630
Description: DMA error
DMA transmission of image data does not complete within the specified period of time.
Causes: Main/Engine PWB
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the main/engine PWB.

Code: 0800
Description: Image processing error
JAM010X is detected twice.
Causes: Main/Engine PWB
Remedy: Replace the main/engine PWB.

Code: 0840
Description: Faults of RTC
(“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check.
Causes: Battery ( main PWB). Main/Engine PWB.
Remedy: Battery ( main PWB) 1. Make sure that the back-up batteries on the main/engine PWB are not shortcircuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main/engine PWB, check the PWB is properly grounded.
Main/Engine PWB Replace the main/engine PWB.

Code: 1810
Description: Paper feeder unit 2 communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Paper feeder. PF main PWB. Main/Engine PWB.
Remedy: Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again.
PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC1) and main/engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PFMain/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. main PWB.

Code: 1820
Description: Paper feeder unit 3 communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Paper feeder. PF main PWB. Main/Engine PWB
Remedy: Paper feeder Check the wiring connection status with paper feeder unit 2 and, if necessary, try connecting it again.
PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC1) and PF main PWB (YC2). 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 1830
Description: Paper feeder unit 4 communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Paper feeder. PF main PWB. Main/Engine PWB.
Remedy: Paper feeder Check the wiring connection status with paper feeder unit 3 and, if necessary, try connecting it again.
PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC1) and PF main PWB (YC2). 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 1900
Description: Paper feeder unit 2 EEPROM error
When writing the data, read and write data does not match 4 times in succession.
Causes: PF main PWB (EEPROM)
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB.

Code: 1910
Description: Paper feeder unit 3 EEPROM error
When writing the data, read and write data does not match 4 times in succession.
Causes: PF main PWB (EEPROM)
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB.

Code: 1920
Description: Paper feeder unit 4 EEPROM error
When writing the data, read and write data does not match 4 times in succession.
Causes: PF main PWB (EEPROM)
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB.

Code: 2000
Description: Main motor steady-state error
After main motor is stabilized, the ready signal is not ready for 1 s continuously.
Causes: Main motor. Main/Engine PWB.
Remedy: Main motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. main motor and main/engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 2010
Description: Main motor startup error
Main motor is not stabilized within 3 s since the motor is activated.
Causes: Main motor. Main/Engine PWB.
Remedy: Main motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. main motor and main/engine PWB (YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the main motor.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 3100
Description: Scanner carriage error
The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor.
Causes: Scanner motor. Home position sensor. Main/Engine PWB.
Remedy: Scanner motor 1. Move the scanner by the hand to check whether it is unusually difficult to move. 2. Check that the scanner driving belt is not disengaged. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and main/engine PWB (YC1) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the scanner motor.
Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and main/engine PWB (YC7) 3. Replace the home position sensor.
Main/Engine PWB Replace the main/engine PWB.

Code: 3200
Description: Exposure lamp error
When a lamp is made to turn on one side at a time, the white standard data at the time of an initial is lower than a rated value.
Causes: CIS. Main/Engine PWB.
Remedy: CIS Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CIS and main/engine PWB (YC2011) Replace the image scanner unit.
Main/Engine PWB Replace the main/engine PWB and check for correct operation.

Code: 3210
Description: CIS lamp error
When a lamp is made both to turn on, the white standard data at the time of an initial is lower than a rated value
Causes: CIS. Main/Engine PWB.
Remedy: CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and main/engine PWB (YC2011) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411.
Main/Engine PWB Replace the main/engine PWB and check for correct operation.

Code: 3300
Description: Optical system (AGC) error One of the gains is FF or 00 during the CIS lamp AGC is being processed.
Causes: CIS. Main/Engine PWB.
Remedy: CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and main/engine PWB (YC2011) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411.
Main/Engine PWB Replace the main/engine PWB and check for correct operation.

Code: 3500
Description: Communication error between scanner and ASIC An error code is detected.
Causes: CIS. Main/Engine PWB.
Remedy: CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and main/engine PWB (YC2011) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411.
Main/Engine PWB Replace the main/engine PWB and check for correct operation.

Code: 3600
Description: Scanner sequence error
Causes: Main/Engine PWB.
Remedy: 1. Execute U021 memory initializing. 2. Replace the main/engine PWB and execute U411.

Code: 4000
Description: Polygon motor steady-state error
After Polygon motor is stabilized, the ready signal is at the H level for 1 s continuously.
Causes: Polygon motor (LSU). Main/Engine PWB.
Remedy: Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and main/engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 4010
Description: Polygon motor synchronization error
After polygon motor is driven, the polygon motor speed won’t stabilize within 10 s.
Causes: Polygon motor (LSU). Main/Engine PWB.
Remedy: Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and main/engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 4200
Description: BD steady-state error
The BD signal is not detected.
Causes: APC PWB (LSU). Main/Engine PWB.
Remedy: APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 6000
Description: Broken fuser heater wire (main)
When the fuser thermistor 1 reaches primary stable temperature after a warm-up start and the fuser thermistor 2 is less than 90 ° C/194 °F.
Causes: Fuser unit. Main/Engine PWB. Power source PWB. Fuser heater.
Remedy: Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and mmain/engine PWB (YC14) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit and execute U167 counter clear. (Deteriorated sensitivity due to the toner adhered to the center thermistor.)
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.
Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC4) and main/ engine PWB (YC14) 2. Replace the power source PWB.
Fuser heater 1. Replace the Fuser unit and execute U167 counter clear.

Code: 6020
Description: Abnormally high fuser thermistor 2 temperature (Center)
Fuser thermistor 2 detects a temperature higher than 210°C/410°F.
Causes: Fuser unit. Main/Engine PWB.
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and main/engine PWB (YC14) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 6030
Description: Broken fuser thermistor 2 wire (Center)
Input from fuser thermistor 2 is 1012 or more (A/D value) continuously for 5 s. Input from fuser thermistor 2 is1012 (A/D value) or more whenthe temperature at the fuser thermistor 1 is 70°C/ 158°F or more.
Causes: Fuser unit. Main/Engine PWB. Fuser thermistor 2. Fuser thermostat (triggered)
Remedy: Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and main/engine PWB (YC14) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit and execute U167 counter clear. (Deteriorated sensitivity due to the toner adhered to the center thermistor.)
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.
Fuser thermistor 2 1. Replace the Fuser unit and execute U167 counter clear.
Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit and execute U167 counter clear.

Code: 6200
Description: Broken fuser heater wire (Sub)
Fuser thermistor 1 does not reach primary stable temperature even after 30 s during warming up. Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 60 s during ready.
Causes: Fuser unit. Main/Engine PWB. Fuser thermistor 1
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and main/engine PWB (YC14) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit and execute U167 counter clear.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.
Fuser thermistor 1 1. Replace the Fuser unit and execute U167 counter clear.

Code: 6220
Description: Abnormally high fuser thermistor 1 temperature (Edge)
Fuser thermistor 1 detects a temperature higher than 230°C/446°F.
Causes: Fuser unit. Main/Engine PWB.
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and main/engine PWB (YC14) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit and execute U167 counter clear.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 6230
Description: Broken fuser thermistor 1 wire (Edge)
Input from fuser thermistor 1 is 1012 or more (A/D value) continuously for 5 s. Input from fuser thermistor 1 is1012 (A/D value) or more whenthe temperature at the fuser thermistor 2 is 70°C/ 158°F or more.
Causes: Fuser unit. Main/Engine PWB.
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and main/engine PWB (YC14) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit and execute U167 counter clear.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 6400
Description: Zero-cross signal error
While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s.
Causes: Fuser unit.
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (CN2) and main/ engine PWB (YC14) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the power source PWB.

Code: 7100
Description: Toner sensor error
Sensor output value of 8 or less.
Causes: Toner sensor. Toner motor. Main/Engine PWB.
Remedy: Toner sensor 1. Check the toner sensor output by U150. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and main/engine PWB (YC9) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit.
Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and main/engine PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 7800
Description: Broken temperature sensor wire
Input from temperature sensor is 0.3 V (A/D value) or less
Causes: Outer temperature sensor. Main/Engine PWB.
Remedy: Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Temperature sensor and main/engine PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the temperature sensor.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 7810
Description: Short-circuited temperature sensor wire
Input from temperature sensor is 0.3 V (A/D value) or more
Causes: Outer temperature sensor. Main/Engine PWB.
Remedy: Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Temperature sensor and main/engine PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the temperature sensor.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 7900
Description: Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively.
Causes: DR PWB. Main/Engine PWB.
Remedy: DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and main/engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit.
Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB.

Code: 9000
Description: Document processor communication error
A communication error from document processor is detected 10 times in succession.
Causes: DP main PWB.
Remedy: 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and main/engine PWB (YC18) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB

Code: 9060
Description: DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively.
Causes: DP main PWB. Device damage of EEPROM.
Remedy: 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB
Device damage of EEPROM Contact the Service Support.

Code: F000
Description: Communication error between Main/Engine PWB and Operation PWB
Causes: Main/Engine PWB. Operation PWB.
Remedy: Main/Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the wirings and connetors between the main/engine PWB and the operation PWB are normal. Main/engine PWB (YC2010) and operation PWB (YC1) 3. Check that the DIMM memories in the main/engine PWB are well conducted and, if not, replace. 4. Execute U021initialize memory. 5. Replace the main/engine PWB.
Operation PWB Replace the operation PWB.

Code: F020
Description: Main/Engine PWB RAM check sum error
Causes: Main memory (RAM)
Remedy: Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main/engine PWB.

Code: F040
Description: Communication error between Main/Engine PWB and Print engine
Causes: Main/Engine PWB
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Repair or replace the wire from the main/ engine PWB, that may be grounded. (Check short-circuit between 5V and 3.3V.) 3. Check the main/engine software and upgrade to the latest, if necessary. 4. If not corrected, replace the main/engine PWB.

Code: F050
Description: Print engine ROM checksum error
Causes: Main/Engine PWB
Remedy: 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Confirm that the EEPROM has been properly installed. 3. Check the main/engine software and upgrade to the latest, if necessary. 4. If not corrected, Replace the main/ engine PWB.

Источник

Кто сейчас на форуме

Re: c0630

Не пропустите эти материалы по теме: