-
#1
Помогите найти расшифровку для кода ошибок для PM 74-2/
- Сообщения
- 2 973
- Реакции
- 1 127
-
#2
тут водятся и инженеры наладки по хейделям. Ты пиши конкретные ошибки, может помогут.
-
#3
Да если честно, каждый день разные ошибки, что бы не бегать печатнику к компьютеру в поисках расшифровки, думал может у кого завалялась, а то с машиной супорт пришел от другой машины.
Operation
3–10
In the case of a malfunction, you will hear a beep
from the Suprasetter 74/105, and the GUI displays an
error message.
1. Click the «Error messages» button. The following help
information is displayed:
Error code
0
Description of error
0
Error remedy
0
2. Follow the instructions to eliminate the error.
Click the «Correct error» button. This action returns
the Suprasetter 74/105 to its initial status and the
function which was interrupted by the error can be
repeated.
Attention: If you hear unusual noises during an error
1
correction that you run following an incorrectly
loaded plate to the drum, do not switch off the
recorder. Wait until the error correction is finished.
Canceling the error correction causes the device to be
set to an undefined state that can only be eliminated
by the service support.
ABC
Edition September 2005
Log in or Sign up
Heidelberg SM102 90 error
Discussion in ‘Heidelberg Printing Presses’ started by Jurij Pavlovic, Jun 23, 2020.
- main board
- sm 102 vs cd 102
- speedmaster
-
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
90 error,help
Jurij Pavlovic,
Jun 23, 2020
#1 -
Steve F
Member- Joined:
- Jun 2013
- Messages:
- 33
- Location:
- Scotland
https://www.colorprintingforum.com/threads/cd-102-cptronic-error-90.12064/
Steve F,
Jun 23, 2020
#2 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Thanks for the help, we have transistors on the control board of the main drive, but after replacing the error 90, the start of the main drive is blocked, the fuses are working
Attached Files:
-
20200623_074543.jpg
- File size:
- 320 KB
- Views:
- 383
-
IMG-3bd07fd52151f52feef2417c77a4a45b-V.jpg
- File size:
- 346.2 KB
- Views:
- 338
Jurij Pavlovic,
Jun 24, 2020
#3 -
CHOCK
Senior Member- Joined:
- Dec 2016
- Messages:
- 2,638
- Location:
- Managua,Nicaragua
Hi sir
need to know what 1) model heidelberg is 2) and what cptronic or cpc??
and what is the error ? 90Blessing
CHOCK,
Jun 24, 2020
#4 -
Mathew
Senior Member- Joined:
- Apr 2010
- Messages:
- 489
- Location:
- Kolding-Denmark
As I can see in the photos, the main motor inverter board is damaged and error 90 refers a general malfunction in main electric cabinet. You have to check the error root on CP2000. Send a photo from malfunctions log from CP2000. How did it happened? During production or machine run or at start up?
Mathew,
Jun 25, 2020
#5 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Good afternoon. Thank you for your interest in my topic.The car was in reserve for six months.A glitch occurred when switching on.Now I have a few days off,I will go back to work to write more information.
Jurij Pavlovic,
Jun 25, 2020
#6 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Here is a photo of the errors:
Attached Files:
-
20200710_140435.jpg
- File size:
- 188 KB
- Views:
- 373
Jurij Pavlovic,
Jul 10, 2020
#7 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Error
Attached Files:
-
20200710_140045.jpg
- File size:
- 108.4 KB
- Views:
- 322
-
20200710_140053.jpg
- File size:
- 123.4 KB
- Views:
- 298
-
20200710_140101.jpg
- File size:
- 150.3 KB
- Views:
- 290
Jurij Pavlovic,
Jul 10, 2020
#8 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Good afternoon sir. The second driver was delivered to us yesterday. We replaced it, but it didn’t help.
Attached Files:
-
20200722_191411.jpg
- File size:
- 65.2 KB
- Views:
- 283
-
20200722_164139.jpg
- File size:
- 75.5 KB
- Views:
- 258
-
20200722_164131.jpg
- File size:
- 72.6 KB
- Views:
- 228
Jurij Pavlovic,
Jul 23, 2020
#9 -
Mathew
Senior Member- Joined:
- Apr 2010
- Messages:
- 489
- Location:
- Kolding-Denmark
Is it a new drive which is delivered yesterday?
Can you send errors from DYN test?
Mathew,
Jul 23, 2020
#10 -
Jurij Pavlovic
Member- Joined:
- Jun 2020
- Messages:
- 11
- Location:
- Lithuanija
Ok
Attached Files:
-
20200724_133122.jpg
- File size:
- 210.2 KB
- Views:
- 288
-
20200724_132750.jpg
- File size:
- 263.7 KB
- Views:
- 265
-
20200724_132837.jpg
- File size:
- 167.7 KB
- Views:
- 268
-
20200724_133027.jpg
- File size:
- 165.7 KB
- Views:
- 260
-
20200724_133103.jpg
- File size:
- 129.1 KB
- Views:
- 286
Jurij Pavlovic,
Jul 24, 2020
#11 -
Advertisement:
-
Adil
Senior Member- Joined:
- Nov 2021
- Messages:
- 567
- Location:
- Casablanca
Press this button and send me the picture, I will direct you to the solution
Attached Files:
-
IMG_20211206_033909.jpg
- File size:
- 234.8 KB
- Views:
- 118
Adil,
Dec 5, 2021
#12
(You must log in or sign up to reply here.)
-
Similar Threads
-
Heidelberg sm102 override sheet
MRTYMM,
Feb 20, 2022, in forum: Heidelberg Printing Presses- Replies:
- 1
- Views:
- 740
- Jack liston
- Feb 21, 2022
-
Heidelberg sm102
Tecnirick,
Nov 17, 2021, in forum: Heidelberg Printing Presses- Replies:
- 3
- Views:
- 1,054
- Tecnirick
- Nov 17, 2021
-
Heidelberg Speedmaster 2005 sm102 10 color
Crawpress123,
Dec 2, 2020, in forum: Heidelberg Printing Presses- Replies:
- 8
- Views:
- 1,306
- Mathew
- Dec 5, 2020
-
Troubleshooting with Heidelbergh SM102 after power failure (block out due to Voltage fluctuations)
DIDNZU,
Feb 7, 2018, in forum: Heidelberg Printing Presses- Replies:
- 10
- Views:
- 4,945
- CHOCK
- Feb 25, 2018
-
HEIDELBERG SM102 Operations Manual
lithoryan,
Sep 20, 2017, in forum: Heidelberg Printing Presses- Replies:
- 0
- Views:
- 3,416
- lithoryan
- Sep 20, 2017
- Your name or email address:
- Do you already have an account?
-
- No, create an account now.
- Yes, my password is:
-
Forgot your password?
-
Stay logged in
Search
-
More…
-
#1
Dear all,
I have tested motor, that is good and LTK does not appear error code FFF5,
Now, in Cptronic appear HAK — 02 ; HAK — 03 ; HAK — 04 in INIT TEST_7 is FFFF SO The dampening units is not run while pile can up and down. I have unplug and plug again but the phenomenon is still appearing.
I do not understand, in service code FFFF is not mistake?
So what problem? any susgession for me
thanks?
-
#2
I may be wrong, but isnt HAK error with the hot air knife for the dryer?
-
#3
I may be wrong, but isnt HAK error with the hot air knife for the dryer?
yep may be you r right
-
#4
HAK are the auxiliary drive boards/modules and HAK 4 represents where the board is- slot#4.
So it looks like you have an error with the HAK board in slot#4
«FFFF» is the Hexadecimal code/ Heidelbergs way of abbreviating the binary code used for diagnosing the Initial test.
1= everything ok, 0= a fault or nothing there. F= 1111 meaning everything ok for the 4 test. FFFF means everything ok for all 16 test.
INIT DISPLAYS are reset to FFFF.
HAK 4 error FFF5 means you have a an error associated with this HAK board.
FFF5 breaks down to FFF0101 meaning you have two faults.
From here you need to find out what this board controls. You do this by using the Service Display:
Go to wrench#2- then hit the «Lock 123» button then use the +/- buttons to go to the HAK screen. Here you will see HAK4 and see the auxiliaries it controls. From here you can trouble shoot what may be wrong. Usually it’s a motor burned out our a ground fault. HAK can control up to 6 auxiliaries so every press can be different.
The best thing to do is call Service once you get to this point and have them confirm what HAK4 is controlling and go from there.
It can very tricky diagnosing these things. Good Luck
Edit — I just noticed you may not have a problem with HAK in particular. You mention LTK, LTK is a Power Part board. Either way what is outlined above will help diagnosing any of the modules- SEK, SSK etc in a CPtronic machine.
Mike
Last edited: Nov 16, 2012
-
#5
Thanks Mike
I have solved the problem, two motor at delivery is plug not true, so i have exchanged it, now the machine is done
Thank you very much
Makdot
|
02/04/2017 19:45
Приветствую. Уважаемые форумчане, помогите пожалуйста, проблема следующая. При двусторонней печати, на ходу машина останавливается с ошибкой — просит перевести её на одностороннюю печать, горит соответствующий значок на пульте. Причём это происходит не с каждым типом бумаги, офсетная 100 и 80 грамм идёт хорошо. Котласс постоянно машина тормозит с этой ошибкой переворота. В чем искать причину?
Рейтинг: 46
проверяйте датчики прохода листа.
для начала очистите от пыли и загрязнений.
далее возможно потребуется настройка.
Makdot
|
03/04/2017 14:46
ПромРемонт 24 писал(а):проверяйте датчики прохода листа.
для начала очистите от пыли и загрязнений.
далее возможно потребуется настройка.
Подскажите пожалуйста где находится этот датчик?
Ответить
Заголовок:
Сообщать мне о получении ответа