Код ошибки 7900 - Не ошибается лишь тот, кто ничего не делает!

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Kyocera
FS4300DN
Code 7900

Code: 7900
Description: Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Causes: Defective connector cable or poor contact in the connector. Defective drum unit.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB and relay-L PWB (YC3) Relay-L PWB and engine PWB (YC15)
Defective drum unit. Replace the drum unit.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки	Описание ошибки	Причина ошибки
0100	Backup memory device error	Defective flash memory. Defective main PWB.
0120	MAC address data error For data in which the MAC address is invalid.	Defective flash memory. Defective engine PWB.
0130	Backup memory read/write error	Defective flash memory. Defective control PWB.
0140	Backup memory data error	Defective flash memory. Defective control PWB.
0150	Control PWB EEPROM error Detecting control PWB EEPROM (U17) communication error.	Improper installation control PWB EEPROM (U17). Defective control PWB. Data damage of control PWB EEPROM (U17).
0170	Billing counting error	Defective control PWB. Data damage of control PWB EEPROM (U17).
0190	Backup memory device error (engine PWB)	Defective engine PWB.
0800	Image processing error JAM010x is detected twice.	Defective main PWB.B.
0840	Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	Defective control PWB. The battery is disconnected from the control PWB.
1010	Lift motor error During driving the lift motor, a motor overcurrent signal is detected for 5 s. This error is detected five times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB or connect-R PWB.
1020	PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1030	PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1040	PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1050	PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1140	BPF lift motor upward error (Bulk paper feeder) BPF lift maximum sensor does not turn on. The lock signal of the motor is detected continuously three times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the motor. Defective BPF lift motor. Defective BPF main PWB.
1150	BPF lift motor downward error (Bulk paper feeder) BPF lift minimum sensor does not turn on. The lock signal of the motor is detected continuously three times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the motor. Defective BPF lift motor. Defective BPF main PWB.
1800	Paper feeder 1 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.
1810	Paper feeder 2 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1820	Paper feeder 3 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1830	Paper feeder 4 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1900	Paper feeder 1/BPF paper feeder EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1910	Paper feeder 2 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1920	Paper feeder 3 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1930	Paper feeder 4 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
2000	Main motor error The main motor ready input is not given for 2 s during the main motor is ON.	Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB.
2010	Main motor steady-state error Stable OFF is detected for 2 s continuously after main motor stabilized.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2200	Drum motor steady-state error The drum motor ready input is not given for 2 s during the drum motor is ON.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB.
2210	Drum motor steady-state error (60/50/45 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB.
2330	Fuser pressure release motor error (Over-current) (60/50/45 ppm model only) The over-current detection signal of the motor is detected continuously twenty times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective PWB.
2340	Fuser pressure release motor error (Timeout) (60/50/45 ppm model only) The position detection sensor is not detected continuously for 30 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective PWB.
2600	PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
2610	PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
2620	PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
2630	PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
4000	Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the polygon motor is ON.	Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.
4200	BD error (laser scanner unit) error	BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.
5100	Main charger high-voltage error Five pages have been printed with the main charger output short-circuited.	Drum unit installed incorrectly. Engine PWB installed incorrectly. Defective engine PWB.
6000	Broken fuser heater wire The temperature does not reach 100°C/212°F after the fuser heater has been turned on continuously for 30 s. The temperature does not rise by 1°C/1.8°F after the fuser heater lamp has been turned on continuously for 15 s during warm-up or at standby.(Only when the detection temperature is less than 200°C.)	Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Broken fuser heater wire.
6020	Abnormally high fuser thermistor temperature Fuser thermistor detects abnormally temperature.	Shorted fuser thermistor. Defective control PWB.
6030	Broken fuser thermistor wire Input from fuser thermistor is 0 (A/D value).	Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire.
6120	Abnormally high fuser thermistor 1 temperature (60/50/45 ppm model) The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less. (40 ppm model) The detection temperature of fuser thermistor 1 is higher than 250°C/482°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 170°C/338°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.	Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.
6130	Broken fuser thermistor 1 wire A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac.or pin. Defective fuser thermistor. Defective engine PWB.
6400	Zero cross signal error The zero cross signal does not reach the control PWB for specified time.	Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Defective power source PWB. Defective control PWB.
7000	Toner motor lock error During driving the toner motor, a motor overcurrent signal is detected for 5 s.	Lump of toner inside toner container. Defective drive transmission system of the toner motor. Defective toner motor. Defective engine PWB.
7100	Toner sensor error Sensor output value of 930 or more continuously for 5 s.	Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB.
7400	Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.r.	Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB.
7410	Drum unit non- installing error The drum unit is not installed or not installed properly. The drum PWB EEPROM does not communicate normally.	The drum unit is not installed. Defective connector cable or poor contact in the connector. Defective drum PWB EEPROM. Defective engine PWB.
7800	Broken external thermistor wire The average of thermistor output value of 1016 or more continuously for 160 ms. The average of thermistor output value of 930 or more continuously for 5 s.	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7810	Short-circuited external thermistor wire The average of thermistor output value of 31 or less continuously for 5 s.	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7900	Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.	Defective connector cable or poor contact in the connector. Defective drum unit.
F000	Main PWB — operation panel PWB communication error	Defective main PWB. Defective operation panel PWB.
F010	Main PWB checksum error	Defective main PWB.
F020	Main PWB RAM checksum error	Defective main memory (RAM) on the main PWB. Defective expanded memory (DIMM).
F040	Main PWB — engine PWB communication error	Defective main PWB. Defective engine PWB.
F041	Main PWB — scanner communication error	Defective main PWB.
F050	Engine ROM checksum error	Defective engine PWB.
F051	Scan engine ROM checksum error	Defective engine PWB.

Содержание

Причины и типы горящей кнопки «Внимание» на принтере Kyocera
Ошибки картриджей
Код C7990
Замятие бумаги
Другие неисправности
Сброс ошибок у принтеров Kyocera своими руками

Для начала необходимо разобраться, какие варианты свечения красной кнопки на принтере Kyocera существуют. В большинстве случаев именно определение характера свечения позволяет устранить проблему, не делая ничего лишнего. Каждый из этих типов связан с конкретной природой проблемы, которую мы рассмотрим ниже.

Медленное мигание лампочки. Если свет тускнеет, а затем ярко вспыхивает и медленно меняет яркость, это может быть одной из двух проблем печати. Первый вызван тем, что закончилась бумага, которую следует проверить и при необходимости вставить заново. Если бумага уже вставлена, но принтер ее не видит, попробуйте слегка отрегулировать ее и отрегулировать ручки, затянув или ослабив их. Вторая причина заключается в том, что тонер в картридже заканчивается, и чтобы проверить это, просто визуально проверьте качество печати готового документа и вспомните, когда принтер заправлялся в последний раз.
Быстрое мигание света. Иногда свет имеет другой коэффициент горения, довольно часто мигая. Это может означать, что был обнаружен неоригинальный картридж, не совместимый с данным устройством. Другой причиной этого явления является переполнение памяти принтера, вызванное попыткой распечатать слишком большой документ. Реже быстрое мигание вызвано перегруженным или засоренным лотком для бумаги, поэтому мы рекомендуем немедленно проверить это и при необходимости устранить неисправность.
Непрерывное мигание индикаторной лампочки. Если возникают ошибки печати и кнопка горит постоянно, стоит проверить, закрыта ли крышка принтера и есть ли тонер в кассете. Вы можете устранить эти неисправности самостоятельно, поэтому трудностей возникнуть не должно. Более редкой и серьезной проблемой является выход из строя барабана формирования изображения. В таких случаях следует обратиться в сервисный центр для дальнейшей диагностики и ремонта.

Теперь, когда вы знаете, какой мигающий рисунок отвечает за те или иные проблемы, вы сможете провести диагностику устройства и понять, какие действия необходимо предпринять. Тем, кто недавно заправил чернильный картридж и столкнулся с этой проблемой, следует перезагрузить принтер, как описано ниже. Всем, кому не удалось самостоятельно устранить ошибку, рекомендуется выполнить следующие шаги, а затем перейти к последнему совету, если и он окажется безуспешным.

Ошибки картриджей

Все современные принтеры страдают от ошибок картриджей. В большинстве случаев они возникают после отгрузки устройства. Решение заключается в извлечении и повторной установке картриджа. Сделать это можно следующим образом (на примере многофункционального устройства Kyocera FS-1040):

Выключите принтер.
На передней панели принтера находится откидная крышка. Откройте откидную крышку.
Под откидной крышкой с левой стороны находится картридж. Извлеките картридж.
Чтобы подстраховаться, проверьте переднюю часть картриджа. Если на контактах есть грязь, удалите ее мягкой безворсовой тканью. Для засохших чернил смочите салфетку в воде и протрите ею контакты.
Замените чернильный картридж, плотно задвинув его до щелчка.
Включите принтер и подождите около 5-10 секунд, пока картридж инициализируется.

Если проблема была связана с картриджем, эта процедура должна помочь ее решить.

Код C7990

Этот номер ошибки в таких моделях, как FS 1020MFP, указывает на то, что бункер для тонера переполнен.

Ошибка C7990

Возможны три причины ошибки C7990:

-плата PWB неисправна;
-Датчик чернил неисправен;
Неисправен блок барабана; — Картридж переполнен — Рекомендуется заменить блок барабана.

Блок барабана формирования изображения

В первых двух случаях обратитесь в сервисный центр.

В третьем случае появляется код C7990, если срок службы барабана изображения не закончился, барабан изображения можно очистить от чернил. Процедура выполняется следующим образом:

1.Откройте переднюю крышку и извлеките блок проявителя.
2.Извлеките барабан с изображением.
3.Осторожно откройте крышку резервуара и удалите чернила.
4.Соберите машину в обратном порядке.

Как видите, ошибку C7990 в принтере Kyocera легко устранить самостоятельно, и к специалисту нужно обращаться только в том случае, если платы действительно неисправны.

Замятие бумаги

Застревание бумаги внутри принтера — распространенная проблема принтеров. Устройства Kyocera не являются исключением. Механизм подачи бумаги состоит из нескольких вращающихся роликов. Если любой из них застрянет, печать не будет выполнена. Если произошло замятие бумаги, на передней панели принтера также появится соответствующее сообщение.

В самых оптимистичных случаях нет необходимости разбирать принтер для извлечения бумаги. Чаще всего он заклинивает прямо на входе. Однако если замятие бумаги произошло внутри принтера, его необходимо удалить.

Другие неисправности

Также могут возникнуть следующие коды:

-C-F040. Выключите и снова включите принтер, нажав кнопку питания.
-J-0511 Код указывает на замятие бумаги под задней крышкой. В инструкциях описано, как удалить бумагу в соответствующем разделе.
-PF. Принтер показывает, что листы были добавлены во входной лоток.

Как видите, японские принтеры Kyocera редко ломаются. Чаще всего ошибки возникают из-за неправильного или невнимательного обращения. Вы можете починить их самостоятельно, но если вы не уверены, лучше обратиться к профессионалу.

Сброс ошибок у принтеров Kyocera своими руками

Сброс ошибок на принтерах Kyocera следует понимать как набор шагов, которые потенциально может выполнить опытный пользователь для восстановления работоспособности печатающих устройств, не прибегая к услугам сервиса.

Ошибка #	Причина	Решение
E-0001	В принтер был установлен совместимый картридж или поврежден чип расходного материала.	Эта проблема может быть решена несколькими способами: 1. установка оригинального картриджа; 2. замена неисправного чипа; 3. перепрошивка принтера — после этого любой картридж может быть установлен в принтер неограниченное количество раз; 4. сброс ошибки — Нажмите кнопки «Режим» и «Сброс» на несколько секунд.
E-0002	Регион используемого картриджа не соответствует принтеру.	Эта проблема может быть решена несколькими способами: 1. установите правильный картридж для региона принтера; 2. Замените микросхему; 3) Обновите микропрограмму принтера.
E-0003	Память в принтере заполнена.	Распечатайте документы, которые уже были отсканированы, или сбросьте операцию с помощью соответствующей кнопки.
E-0007	Тонер-картридж закончился.	Замените новый оригинальный тонер-картридж, совместимый тонер-картридж или перезарядите картридж.
E-0008	Одна из крышек принтера не закрыта.	Закройте переднюю и заднюю крышки принтера, звучно щелкнув.
E-0009	Лоток для печати заполнен.	Извлеките отпечатанные листы бумаги, затем нажмите кнопку Старт, чтобы возобновить печать.
E-0012	Память принтера заполнена.	Уменьшите разрешение печати до 600 точек на дюйм.
E-0014	Установлен размер бумаги, который не поддерживается принтером.	Замените бумагу на совместимую по размеру. Иногда функциональность принтера может быть ограничена на уровне программного обеспечения. Для расширения диапазона размеров рекомендуется обновить программное обеспечение принтера.
E-0015	1 Принтер не имеет источника питания. 2. сетевой кабель не подключен. 3. на персональном компьютере отсутствует драйвер.	Проверьте целостность сетевого кабеля. Включите принтер. При необходимости установите драйвер.
E-0018	Выбранный файл отсутствует в очереди печати.	Сбросьте операцию, нажав кнопку «Сброс». Затем выберите новый файл и продолжите печать.
E-0019	Формат печати не поддерживается принтером.	Сбросьте действие, нажав кнопку «Сброс».
J-0511	Бумага замята.	Осторожно извлеките оставшуюся бумагу из корпуса принтера.
ПФ	Во входном лотке нет бумаги.	Вставьте бумагу во входной лоток и возобновите печать, нажав кнопку Старт.

Источники

https://Lumpics.ru/kyocera-printer-does-not-print-attention-button-is-on/
https://ru.NoDevice.com/articles/printers/does-not-print-a-kyocera-printer
https://www.dvenashka.ru/2021/11/kody-oshibok-printerov-kyocera-i-ih-sbros.html
https://computermaker.info/ecosys-fs-1020mfp-oshibka-e7.html
http://printergid.ru/neispravnosti/oshibki-kyocera
https://moscowtoner.ru/kody-oshibok-u-printerov-kyocera/

Источник

Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки	Описание ошибки	Причина ошибки
0030	FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.	Defective FAX control PWB.
0060	Control PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard	Control PWB
0070	FAX control PWB incompatible detection Error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.	FAX control PWB (The FAX PWB installed will not be the one designed for the machine.
0100	Backup memory device error	EEPROM (Control PWB)
0110	Backup memory data error	EEPROM (Control PWB)
0120	MAC address data error For data in which the MAC address is invalid.	EEPROM (Control PWB)
0130	Backup memory read/write error (main NAMD)	Flash memory (Control PWB)
0140	Backup memory data error (main NAND)	Flash memory (Control PWB)
0150	Backup memory read/write error (control PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.	EEPROM (Control PWB)
0160	Backup memory data error (control PWB) Reading data from EEPROM is abnormal.	EEPROM
0170	Billing counting error The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter.	EEPROM. Control PWB
0180	Machine number mismatch Machine number of control does not match.	Data damage of EEPROM.
0190	Backup memory device error (control PWB)	Control PWB
0080	Image processing error JAM010X is detected twice.	Control PWB.
0800	Image processing error JAM010X is detected twice.	Control PWB.
0830	FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.	FAX software. FAX control PWB.
0420	Paper feeder communication error Communication error between control PWB and optional paper feeder.	Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF mainPWB.
0830	FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.	Defective fax software. Defective FAX control PWB.
0840	Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	Defective control PWB. The battery is disconnected from the control PWB.
0870	FAX control PWB to control PWB high capacity data transfer problem High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.	Improper installation FAX control PWB. Defective FAX control PWB or control PWB.
0920	Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.	Defective FAX control PWB.
0970	24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second.	Connect right PWB. Control PWB
1010	Lift motor error (50/60 ppm model only) After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the lift motor. Lift motor. Connect right PWB. Control PWB.
1020	PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1030	PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.	Dottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1040	PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1050	PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1800	Paper feeder 1 communication error A communication error is detected 10 times in succession.	Paper feeder. Connector cable or poor contact in the connector. PF main PWB. Control PWB.
1810	Paper feeder 2 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB.
1820	Paper feeder 3 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB
1830	Paper feeder 4 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB
1900	Paper feeder 1 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1910	Paper feeder 2 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1920	Paper feeder 3 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1930	Paper feeder 4 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
2000	Main motor startup error Main motor is not stabilized within 2 s since the motor is activated.	Main motor. Connect right PWB. Control PWB
2010	Main motor steady-state error After main motor is stabilized, the ready signal is not ready for 2 s continuously.	Main motor. Connect right PWB. Control PWB.
2200	Drum motor drive error (50/60 ppm model only) The drum motor is not stabilized within 2 s after driving starts.	Connector cable or poor contact in the connector. Drive transmission system of the drum motor. Drum motor. Connect right PWB. Control PWB.
2210	Drum motor steady-state error (50/60 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.	Connector cable or poor contact in the connector. Drive transmission system of the drum motor. Drum motor. Connect right PWB. Control PWB.
2330	Envelope motor error (Over-current) (50/60 ppm model only) The over-current detection signal of the motor is detected continuously twenty times.	Connector cable or poor contact in the connector. Drive transmission system of the envelope motor. Envelope motor. Connect left PWB. Control PWB.
2340	Envelope motor error (Timeout) (50/60 ppm model only) The position detection sensor is not detected continuously for 30 s.	Connector cable or poor contact in the connector. Drive transmission system of the envelope motor. Envelope motor. Connect left PWB. Control PWB.
2600	PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. DPF drive motor. DPF main PWB.
2610	PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
2620	PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
2630	PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
3100	Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor.	Image scanner motor. Home position sensor. CCD PWB. Control PWB.
3200	Exposure lamp error When a lamp is made to turn on one side at a time, the white standard data at the time of an initial is lower than a rated value.	LED PWB. CCD PWB. Control PWB.
3500	Communication error between scanner and ASIC An error code is detected.	CCD PWB. Control PWB.
4000	Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 20 s continuously.	Polygon motor (LSU). Control PWB.
4200	BD steady-state error The BD signal is not detected.	PD PWB (LSU). Control PWB.
5100	Chager current error When the current value measured at the time of potential adjustment is less than 20 mcA. The error of the charge current before toner installation. The error of the charge current before printing.	Connector cable or poor contact in the connector. High voltage PWB. Control PWB.
6000	Broken fuser heater wire (Center) (50/60 ppm model) Fuser thermistor 2 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start. (40 ppm model) Fuser thermistor 1 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start.	Fuser unit. Fuser thermistor connect PWB. Control PWB. Power source PWB. Fuser heater.
6020	Abnormally high fuser thermistor 2 temperature (Center) (50/60 ppm model only) Fuser thermistor 2 detects a temperature higher than 235°C/455°F. In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.	Fuser unit. Fuser thermistor connect PWB. Control PWB.
6030	Broken fuser thermistor 2 wire (Center) (50/60 ppm model only) Input from fuser thermistor 2 is 1019 or more (A/D value) continuously for 4 s.	Fuser unit. Fuser thermistor connect PWB. Control PWB. Fuser thermistor 2. Fuser thermostat (triggered). Power source PWB
6120	Abnormally high fuser thermistor 1 temperature (50/60 ppm model) The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less. (40 ppm model) The detection temperature of fuser thermistor 1 is higher than 250°C/482°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 170°C/338°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.	Connector pin. Triac. Fuser thermistor. Contrl PWB.
6130	Broken fuser thermistor 1 wire (50/60 ppm model only) A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.	Connector cable or poor contact in the connector. Connector pin. Triac. Fuser thermistor. Fuser thermistor connect PWB. Control PWB.
6400	Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 2 s.	Fuser unit. Power source PWB. Connect right PWB. Control PWB.
7000	Toner motor error During driving the toner motor, an over-current detection signal is detected at intervals of 10 ms as for 300 accumulation.	Connector cable or poor contact in the connector. Drum unit. Connect left PWB. Control PWB.
7100	Toner sensor error Sensor output value of 930 or more continuously for 5 s.	Toner sensor. Toner motor. Connect left PWB. Control PWB.
7400	Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.	Connector cable or poor contact in the connector. Toner sensor. Connect left PWB. Control PWB.
7410	Drum unit type mismatch error The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.	Connector cable or poor contact in the connector. Toner sensor. Connect left PWB. Control PWB.
7800	Broken temperature sensor wire Input from temperature sensor is 1019 or more continuously for 160 ms. Input from temperature sensor is 930 or more continuously for 5 s.	Temperature sensor. Control PWB.
7810	Short-circuited temperature sensor wire Input from temperature sensor is 31 or less continuously for 5 s.	Temperature sensor. Control PWB.
7900	Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.	DR PWB. Connect left PWB. Control PWB.
F000	Communication error between Control PWB and Operation PWB	Control PWB. Operation PWB.
F010	Control PWB checksum error	Control PWB.
F020	Control PWB RAM check sum error	Main memory (RAM).
F040	Communication error between Controller and Print engine	Control PWB.
F041	Communication error between Controller and Scan engine	Control PWB.
F050	Print engine ROM checksum error	Control PWB.
F051	Scan engine ROM checksum error	Control PWB.

Источник

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Kyocera
FS4300DN
Code 7900

Code: 7900
Description: Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Causes: Defective connector cable or poor contact in the connector. Defective drum unit.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB and relay-L PWB (YC3) Relay-L PWB and engine PWB (YC15)
Defective drum unit. Replace the drum unit.

Источник

Code: 0100
Description: Backup memory device error
Causes: Defective flash memory.
Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: 0120
Description: MAC address data error
For data in which the MAC address is invalid.
Causes:
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0130
Description: Backup memory read/write error (main PWB)
Causes: Defective flash memory.
Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: 0140
Description: Backup memory data error (main PWB)
Causes: Defective flash memory.
Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: 0150
Description: Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error.
Causes:
Remedy: Improper installation engine PWB EEPROM. Check the installation of the EEPROM and remedy if necessary.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 0160
Description: Backup memory data error (engine PWB)
Causes: Defective EEPROM.
Defective engine PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: 0170
Description: Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters.
Causes:
Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.

Code: 0190
Description: Backup memory device error (engine PWB)
Causes: Defective engine PWB.
Remedy: Replace the engine PWB and check for correct operation.

Code: 0800
Description: Image processing error
JAM010x is detected twice.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor 1/2 and fuser thermistor connect PWB(YC1/2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Defective fuser thermistor. Replace the fuser thermistor connect PWB. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operations.

Code: 0840
Description: Faults of RTC
Unable to communicate with the RTC device normally. The RTC data is mismatched due to dead battery or short-circuit with the metal part.
Causes:
Remedy: Other RTC device failure due to dead battery or short-circuit with the metal part. Restart the main unit and set the correct time from the operation panel. Repair it if the battery comes off from the main PWB.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 1010
Description: Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected five times successively.
Causes:
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor and engine PWB (YC13)
Defective drive transmission system of the lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective lift motor. Replace the lift motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1020
Description: PF lift motor 1 error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.
Causes:
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 1.
Defective PF main PWB. Replace the PF main PWB.

Code: 1030
Description: PF lift motor 2 error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.
Causes:
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 2.
Defective PF main PWB. Replace the PF main PWB.

Code: 1040
Description: PF lift motor 3 error (paper feeder)
After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.
Causes:
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 3 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 3.
Defective PF main PWB. Replace the PF main PWB.

Code: 1050
Description: PF lift motor 4 error (paper feeder)
After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.
Causes:
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 4 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 4.
Defective PF main PWB. Replace the PF main PWB.

Code: 1140
Description: BPF lift motor upward error (Bulk paper feeder)
BPF lift maximum sensor does not turn on. The lock signal of the motor is detected continuously three times.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective BPF lift motor. Replace the BPF lift motor.
Defective BPF main PWB. Replace the BPF main PWB.

Code: 1150
Description: BPF lift motor downward error (Bulk paper feeder)
BPF lift minimum sensor does not turn on. The lock signal of the motor is detected continuously three times. When detecting an overcurrent detection signal.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective BPF lift motor. Replace the BPF lift motor.
Defective BPF main PWB. Replace the BPF main PWB.

Code: 1800
Description: Paper feeder 1 communication error
A communication error is detected 10 times in succession.
Causes:
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective PF main PWB. Replace the PF main PWB.

Code: 1810
Description: Paper feeder 2 communication error
A communication error is detected 10 times in succession.
Causes:
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB.

Code: 1820
Description: Paper feeder 3 communication error
A communication error is detected 10 times in succession.
Causes:
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB.

Code: 1830
Description: Paper feeder 4 communication error
A communication error is detected 10 times in succession.
Causes:
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB.

Code: 1900
Description: Paper feeder 1/BPF paper feeder EEPROM error
When writing the data, the write data and the read data is not in agreement.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Replace the PF main PWB or the BPF main PWB.

Code: 1910
Description: Paper feeder 2 EEPROM error
When writing the data, the write data and the read data is not in agreement.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Replace the PF main PWB.

Code: 1920
Description: Paper feeder 3 EEPROM error
When writing the data, the write data and the read data is not in agreement.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Replace the PF main PWB.

Code: 1930
Description: Paper feeder 4 EEPROM error
When writing the data, the write data and the read data is not in agreement.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Replace the PF main PWB.

Code: 2000
Description: Main motor drive error
The main motor is not stabilized within 2 s after driving starts.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective main motor. Replace the main motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2010
Description: Main motor steady-state error
Stable OFF is detected for 2 s continuously after main motor stabilized.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective main motor. Replace the main motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2200
Description: Drum motor drive error
The drum motor is not stabilized within 2 s after driving starts.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective drum motor. Replace the drum motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2210
Description: Drum motor steady-state error
Stable OFF is detected for 2 s continuously after drum motor stabilized.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective drum motor. Replace the drum motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2330
Description: Fuser pressure release motor error (Over-current)
The over-current detection signal of the motor is detected continuously twenty times.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC3) and engine PWB(YC2)
Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser pressure release motor. Replace the fuser pressure release motor.
Defective PWB. Replace the relay-L PWB or engine PWB.

Code: 2340
Description: Fuser pressure release motor error (Timeout)
The position detection sensor is not detected continuously for 30 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC1) and engine PWB(YC2)
Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser pressure release motor. Replace the fuser pressure release motor.
Defective PWB. Replace the relay-L PWB or engine PWB.

Code: 2600
Description: PF drive motor 1 error (paper feeder 1)
When the PF drive motor is driven, error signal is detected continuously for 2 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 1 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 1.
Defective PF main PWB. Replace the PF main PWB.

Code: 2610
Description: PF drive motor 2 error (paper feeder 2)
When the PF drive motor is driven, error signal is detected continuously for 2 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 2 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 2.
Defective PF main PWB. Replace the PF main PWB.

Code: 2620
Description: PF drive motor 3 error (paper feeder 3)
When the PF drive motor is driven, error signal is detected continuously for 2 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 3 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 3.
Defective PF main PWB. Replace the PF main PWB.

Code: 2630
Description: PF drive motor 4 error (paper feeder 4)
When the PF drive motor is driven, error signal is detected continuously for 2 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 4 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 4.
Defective PF main PWB. Replace the PF main PWB.

Code: 4000
Description: Polygon motor synchronization error
The polygon motor is not stabilized within 20 s after driving starts.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Polygon motor and engine PWB (YC15)
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4101
Description: BD steady-state error
When the value of Register BDSET is 1 after setting Register BDSET as one and passing by BD1 cycle.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB(YC1) and engine PWB (YC16) APC PWB(YC2) and PD PWB(YC1)
Defective PD PWB. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 5100
Description: Chager current error When the current value measured at the time of potential adjustment is less than 20 uA.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Chager unit and high voltage PWB High voltage PWB (YC101) and engine PWB (YC19)
Defective high voltage PWB. Replace the high voltage PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6000
Description: Broken fuser heater wire
The detection temperature of fuser thermistor 2 is 100 °C/212°F or less after the fuser heater lamp has been turned on continuously for 30 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser heater and power source PWB (YC2) Fuser thermistor and Fuser thermistor connect PWB(YC1 and YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Fuser thermostat triggered. Reinsert the fuser unit.
Broken fuser heater wire.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6020
Description: Abnormally high fuser thermistor 2 temperature
The detection temperature of fuser thermistor 2 is higher than 235°C/ 455°F.
In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.
Causes:
Remedy: Deformed connector pin.
Defective triac.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030
Description: Broken fuser thermistor 2 wire
A/D value of the fuser thermistor 2 exceeds 1019 bit continuously for 4 s during warming up.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6120
Description: Abnormally high fuser thermistor 1 temperature
The detection temperature of fuser thermistor 1 is higher than 245°C/ 473°F.
In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.
Causes:
Remedy: Deformed connector pin.
Defective triac.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6130
Description: Broken fuser thermistor 1 wire
A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC1) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6400
Description: Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 2 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and engine PWB (YC1)
Defective power source PWB or engine PWB. Replace the power source PWB or the engine PWB and check for correct operation.

Code: 7100
Description: Toner sensor error
Sensor output value of 930 or more continuously for 5 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7400
Description: Developer unit non-installing error
Sensor output value of 31 or less continuously for 5 s.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7410
Description: Drum unit type mismatch error
The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the drum unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7800
Description: Broken external thermistor wire
The average of thermistor output value of 93 or less.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
Defective temperature sensor. Replace the operation PWB.

Code: 7810
Description: Short-circuited external thermistor wire
The average of thermistor output value of 930 or more.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
Defective temperature sensor. Replace the operation PWB.

Code: 7900
Description: Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective drum unit. Replace the drum unit.

Code: F000
Description: Main PWB — operation PWB communication error
Causes:
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB(YC1) and engine PWB (YC17)
Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective operation PWB. Replace the operation PWB and check for correct operation.

Code: F010
Description: Main PWB checksum error
Causes: Defective main PWB.
Remedy: Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.

Code: F020
Description: Main PWB RAM checksum error
Causes:
Remedy: Defective main memory (RAM) in main PWB Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective expended memory (DIMM) Replace the expansion memory (DIMM). Also in the case of the capacity besides specification, it displays.

Code: F040
Description: Main PWB — print engine communication error
Causes:
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: F050
Description: Print engine ROM checksum error
Causes: Defective engine PWB.
Remedy: Turn the main power switch off/on to restart the machine. If the error is not resolved, replace engine PWB.

Источник

Правила форума
Картинки и фотографии (если они нужны в сообщении) надо загружать только как вложения к своему сообщению (через кнопку Добавить файлы). Тогда картинки будут автоматически отображаться в сообщении.

Yuzorg98: Сообщения: 29; Стаж: 9 месяцев

Kyocera Ecosys P3150dn

Сообщение

Yuzorg98 » 03 апр 2023, 15:32

В общем начал выдавать ошибку как на фото
Включается,пишет замятие, вытаскиваю блок фотоузла ( он нормальный, считай новый) вместе с катриком, закрываю принтер и вылезает она.
Ставил с другого принтера фотоузел с катриком, та же ситуация.
Внутри ничего нет, никакой бумаги.
Печка вроде нормальная, только вал прижима малость скукожился.
В чём может быть проблема?
Перерыл весь инет и форумы, ничего не нашёл.

Yuzorg98: Сообщения: 29; Стаж: 9 месяцев

Kyocera Ecosys P3150dn

Сообщение

Yuzorg98 » 03 апр 2023, 15:47

стронций писал(а): ↑03 апр 2023, 15:44
Ну если дело не в переполненном бункере с отработкой и ДРАМом, то как вариант еще, это неисправна PWB-плата.

Где она находится?
Бункер который сборку я его почистил, он пустой, да и не сказать что был забит.
Что может быть с драмом?

pc-porta: Сообщения: 753; Стаж: 1 год 5 месяцев; Благодарил (а): 16 раз; Поблагодарили: 116 раз; Репутация:

Kyocera Ecosys P3150dn

Сообщение

pc-porta » 03 апр 2023, 15:49

Картинка не грузилась ….. вот и нету.
это ошибка инициализации блока DK-3150. Может контакт какой обломился на колодке ? или мусор какой в ней (та часть — которая в МФУ стоит) затёрся ?

Yuzorg98: Сообщения: 29; Стаж: 9 месяцев

Kyocera Ecosys P3150dn

Сообщение

Yuzorg98 » 03 апр 2023, 16:02

pc-porta писал(а): ↑03 апр 2023, 15:49
Картинка не грузилась ….. вот и нету.
это ошибка инициализации блока DK-3150. Может контакт какой обломился на колодке ? или мусор какой в ней (та часть — которая в МФУ стоит) затёрся ?

вроде всё целое
грязи никакой нет

Отправлено спустя 14 минут 31 секунду:

стронций писал(а): ↑03 апр 2023, 15:50
Плата PWB находиться, если смотреть спереди, по правую руку за пластиком.

Нашёл, вставил аналогичную плату, но там ошибка 6120, и она же вылезла на этом принтере
Перепрошивка его поможет? С ошибкой 7900?

стронций: Сообщения: 341; Стаж: 1 год 5 месяцев; Благодарил (а): 12 раз; Поблагодарили: 36 раз; Репутация:

Kyocera Ecosys P3150dn

Сообщение

стронций » 03 апр 2023, 16:25

Прошить в принципе можно, хуже то не будет. Надо заказать свежую версию прошивки и смотреть фаил-блокнот «History» который идет, почти, со всеми прошивками. Там можно уточнить все об исправлениях ошибок, и каких конкретно ошибок.
Ну я что то сомневаюсь что прошивка поможет.

стронций: Сообщения: 341; Стаж: 1 год 5 месяцев; Благодарил (а): 12 раз; Поблагодарили: 36 раз; Репутация:

Kyocera Ecosys P3150dn

Сообщение

стронций » 03 апр 2023, 16:38

Если печная ошибка возникла то надо печку первым делом вскрыть и осмотреть. Вероятность что придется менять блок печки целиком 100%.
Как я и писал ранее если и отремонтировать печку, то есть подложить кусочек термопленки туда то и туда то, то все чудным образом заработает… Ну заработать то заработает, но появиться другая проблема, это уже проверено как минимум на 3-х FK-3130(3300).

Yuzorg98: Сообщения: 29; Стаж: 9 месяцев

Kyocera Ecosys P3150dn

Сообщение

Yuzorg98 » 03 апр 2023, 17:45

стронций писал(а): ↑03 апр 2023, 16:38
Если печная ошибка возникла то надо печку первым делом вскрыть и осмотреть. Вероятность что придется менять блок печки целиком 100%.
Как я и писал ранее если и отремонтировать печку, то есть подложить кусочек термопленки туда то и туда то, то все чудным образом заработает… Ну заработать то заработает, но появиться другая проблема, это уже проверено как минимум на 3-х FK-3130(3300).

Прошивка не помогла
Так же ошибка 7900

pc-porta: Сообщения: 753; Стаж: 1 год 5 месяцев; Благодарил (а): 16 раз; Поблагодарили: 116 раз; Репутация:

Kyocera Ecosys P3150dn

Сообщение

pc-porta » 03 апр 2023, 17:51

ну — я тоже в сомнении …. но — факт : ошибки 7900 — это ошибка инициализации блока DK от 3100 до 3190
если есть желание — соберите франкенштейна : перекиньте плату PWB и термистр в печке

Последний раз редактировалось pc-porta 03 апр 2023, 17:54, всего редактировалось 1 раз.

Yuzorg98: Сообщения: 29; Стаж: 9 месяцев

Kyocera Ecosys P3150dn

Сообщение

Yuzorg98 » 03 апр 2023, 17:53

pc-porta писал(а): ↑03 апр 2023, 17:51
ну — я тоже в сомнении …. но — факт : ошибки 7900 — это ошибка инициализации блока DK от 3100 до 3190

Гугл на эту тему мне толком ничего говорил, видать я один такой с этой ошибкой

dviz: Сообщения: 204; Стаж: 1 год 5 месяцев; Откуда: Ярославль; Благодарил (а): 15 раз; Поблагодарили: 25 раз; Репутация:

Kyocera Ecosys P3150dn

Сообщение

dviz » 03 апр 2023, 18:01

7900 — это либо плохой контакт с платой в драм-юните либо проблема с микрухой eeprom в на этой плате. Без драма аппарат естесствено будет выдавать эту ошибку.
Если показывает замятие — решайте проблему с замятием, а не с драмом.