Куосера 2530 ошибка 3200

Модератор: vetal

Прилепить пост

Сообщение Andreyak777 » Ср ноя 18, 2015 3:55 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети

Прилепить пост

Сообщение FLHF » Чт ноя 19, 2015 10:41 am

Аватар пользователя

FLHF

  

Осматривается

  • Не в сети

Прилепить пост

Сообщение Andreyak777 » Чт ноя 19, 2015 1:49 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети
  • [SCANNER ERROR] Lamp Error Kyocera FS-1016

    мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

    3
    6645

    Усатый Полосатый
    Перейти к последнему сообщению
    Вс окт 28, 2018 11:08 pm
  • Kyocera FS-1120d индикатор «Нет бумаги»

    vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

    11
    15142

    СТРОНЦИЙ
    Перейти к последнему сообщению
    Вт ноя 02, 2021 2:24 pm
  • Kyocera 1035 «бледная» печать

    srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

    2
    13949

    srMax
    Перейти к последнему сообщению
    Пт янв 23, 2015 2:49 pm
  • Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

    manik.76 в форуме Принтеры, МФУ, копиры формата A3

    3
    9650

    dviz
    Перейти к последнему сообщению
    Пн фев 20, 2017 1:35 pm
  • Kyocera Ecosys M2635dn «поворот» изображения

    Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

    10
    6103

    MatrixAgent
    Перейти к последнему сообщению
    Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 79

Источник

полезная информация

21:40

kyocera taskalfa 181 ошибка C3200

kyocera taskalfa 181 ошибка C3200

Ошибка C3200 означает «Отсутствие освещения экспонирующей лампы, обнаруживается в начале копирования.» следовательно добираемся до лампы сканера.

МФУ возрастной, и собрал за свою жизнь очень много пыли, наша задача прочистить сканер от пыли а именно: лампу сканера, отражающие зеркала под лампой, и возле лампы, можно слегка влажной тряпкой.

После того как вы все прочистили, собираем и проверяем если не заработало прозваниваем шлейф указанный на фото выше,  прозваниваем в разных положениях шлейфа, так как контакт может появляться и пропадать, если все в порядке, но аппарат по прежнему выдает ту же ошибку, то вам не повезло либо замена платы управления либо замена сканера вам поможет.
  • 1
  • 2
  • 3
  • 4
  • 5

Просмотров: 1107 |

| Рейтинг: 0.0/0

Добавлять комментарии могут только зарегистрированные пользователи.

[

Регистрация

|

Вход

]

Источник

Если при работе с копировальном аппаратом у вас возникли проблемы, и система выдает код ошибки, вы можете идентифицировать ее с помощью данной таблицы.
Коды ошибок Kyocera-Mita указаны для более поздних моделей копиров. Если вы являетесь владельцем более ранней модели, необходимо к трехзначному коду ошибки прибавить знак «0».

Общие ошибки
 

Код ошибки Описание
0030 Fax control PWB system problem
0070 Fax control PWB incompatibility detection problem
0100 Backup memory read/write problem (main board)
0110 Backup memory data problem (main board)
0120 Drum EEPROM read/write problem (для 2550)
0130 Backup memory read/write problem (main PCB EEPROM) (для 1650/2050/2550)
0140 Backup memory data problem (main PCB EEPROM) (для 1650/2050/2550)
0150 Backup memory read/write problem (engine board)
0160 Backup memory data problem (engine board)
0170 Accounting count problem
0180 Machine number mismatch
0210 Communication problem between the main board and engine board (для KM-1500/1620/2020/1635/2035/1650/2050/2550/6030/8030, FS-1018/1118)
Communication problem between the main board and operation board (для KM-1525/1530/2030/2530/3530/6230/4530/5530/6330/7530)
0240 Printer board PWB communication problem
0250 Scanner network board communication problem
0280 Communication problem between the fax control PWB and main PWB
0320 Side deck communication problem
0340 Finisher communication problem
0410 Optional DP communication problem
0420 Optional first paper feeder communication problem
Large paper deck /paper feed desk communication problem /Side deck communication problem
0440 Finisher communication problem
0450 Mailbox communication problem
0470 Switchback unit communication problem
0500 Optional second paper feeder communication problem
0510 Optional third paper feeder communication problem
0600 DIMM problem (для 2530/3530)
0610 Bitmap (DIMM) problem
0620 Memory input interface problem
0630 DMA problem
0640 Hard disk drive problem
0800 Image processing problem (JAM05 is detected twice)
0820 Fax control PCB CG ROM checksum error
0830 Flash ROM program area checksum error
0860 Fax control PCB software switch checksum error
0870 Fax control PWB to main PWB high capacity data transfer problem
0880 Fax control PWB program archive problem
0890 Fax control PCB CG font archive problem
0900 Fax software incompatibility detection problem
0920 Fax file system error
0960 Developer EEPROM read/write problem (для 2550/6030/8030)
1000 Exposure lamp problem
1010 Lift motor 1 error
1020 Lift motor 2 error
1030 Lift motor 3 error
1040 Lift motor 4 error
1100 Paper deck motor 1 problem [Drawer 3]
1110 Paper deck motor 2 problem [Drawer 4]
1120 Deck right lift position problem
1130 Deck left lift position problem
1140 Side deck lift motor (going up) problem
1150 Side deck lift motor (going down) problem
1160 Large paper deck (paper feed desk) sequence problem
1170 Large paper deck (paper feed desk) incorrect type problem
2000 Main motor problem
Image forming motor problem (для 6230/4530/5530/6330/7530)
2500 Paper feed motor problem
2550 Paper conveying motor problem (для 4530/5530)
2600 Deck conveying motor /desk drive motor problem
2640 Side deck drive motor problem
3100 Scanner carriage problem
3200 Exposure lamp problem
3300 Optical system (AGC) problem
4000 Polygon motor synchronization problem
4010 Polygon motor steady-state problem
4100 BD initialization (A) problem
4110 BD initialization (B) problem
4200 BD steady-state problem
5100 Main charger problem
5110 Transfer/separation high voltage problem
5300 Broken cleaning lamp wire
5500 Drum surface potential sensor problem 1
5510 Drum surface potential sensor problem 2
5600 Drum surface potential problem 1
5610 Drum surface potential problem 2
6000 Broken fixing heater wire
6020 Abnormally high fixing unit thermistor temperature
6030 Broken fixing unit thermistor
6050 Abnormally low fixing unit thermistor temperature
6100 Broken fixing heater wire
6200 Abnormally low fixing unit thermistor temperature
6300 Abnormally high fixing unit thermistor temperature
6400 Zero-crossing signal problem
6410 Fixing unit connector insertion problem
6420 Fixing fuse cut problem
6420 Broken fixing unit thermistor wire
7100 Toner sensor problem
7300 Broken external temperature thermistor wire (для KM-1505/1510/1810/4230/5230/6230)
Toner sensor problem/ Toner hopper problem (для KM-2530/3530/3035/4035/5035/6230/4530/5530/6330/7530/6030/8030)
7310 Short-circuited external temperature thermistor
7400 Image formation unit connector insertion problem
Developing unit connector insertion problem (для 2550)
7410 Drum unit connector insertion problem
7750 Drum type mismatch problem A (для 1635/2035)
7760 Drum type mismatch problem B (для 1635/2035)
7800 Broken external temperature thermistor
7810 Short-circuited external temperature thermistor

KM-1500, FS-1018/1118 (KM-1820)

Код ошибки Описание
0220 Communication problem between the main board and operation board (для 1018/1118)
F— Controller system error (для 1018/1118)
F010 ROM checksum error (для 1118)
F012
7980 Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets)
7990 Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more)

KM-1505/1510/1810/1525/1530/2030

Код ошибки Описание
0210 Printer board communication problem (для 1505/1510/1810)
0400 DIMM problem
0410 Bitmap problem
0430 DMA problem
1040 Optical system problem (AGC)

Kyocera-Mita 3035/4035/5035

Код ошибки Описание
0100 Operation unit PCB backup memory read/write error
0110 Operation unit PCB backup memory data problem
0210 MMI communication problem
0320 Energy save communication problem
7450 Image formation unit fuse cut problem

Kyocera Mita 4230/5230

Код ошибки Описание
0010 Memory copy PCB 1 communication problem
0030 Memory copy PCB 2 communication problem
0100 RAM/ROM problem
0220 Communication problem between the engine PCB and main PCB
0230 Scanner communication problem
0260 Memory copy PCB 1 communication problem
0320 Large paper deck communication problem /Paper feed desk communication problem
0360 Memory copy PCB 2 communication problem
0370 Communication microcomputer problem
1040 Optical system problem (AGC)
2100 Paper conveying motor problem
2200 Side registration motor problem
2300 Paper feed motor problem
2310 Desk drive motor problem
2410 Upper lift motor problem
2420 Lower lift motor problem
2430 Upper desk lift motor problem
2440 Lower desk lift motor problem
3320 Scanner watchdog problem
3400 Original detection position problem
7400 Toner hopper problem
9200 Deck paper conveying motor problem
9210 Paper deck motor 1 problem
9220 Paper deck motor 2 problem
9230 Right lift position problem
9240 Left lift position problem

Kyocera-Mita 6030/8030

Код ошибки Описание
0060 Main PWB type mismatch error
0130 Backup memory (EEPROM) device problem
0140 Backup memory (EEPROM) data problem
0220 Scanner communication problem
0330 Relay board communication problem
0460 Duplex unit communication problem
0470 Sheet inserter communication problem (optional document finisher)
0500 Paper feed unit communication error (cassette 1 and 2)
0510 Paper feed unit communication error (cassette 3 and 4)
0700 Side feeder EEPROM error (optional side feeder)
0750 Document finisher EEPROM error
0970 Cleaning unit EEPROM error
1200 Duplex side registration motor error
2100 Developing motor error
2200 Drive motor error
2300 Fuser motor error
2550 Transfer motor error
3210 CIS lamp problem
3310 Optical system (AGC) problem (DP)
3500 Communication error between scanner and SHD
3900 Backup memory read/write error (scanner PWB)
3910
4120 BD initialization (C) problem
7200 Broken drum thermistor wire
7210 Shorted drum thermistor
9040 DP lift motor going up error
9050 DP lift motor going down error
9060 DP EEPROM error
9070 Communication problem between DP and SHD
9080 Communication problem between DP and CIS

Kyocera Mita 6230

Код ошибки Описание
0010 Memory PCB communication problem
0100 RAM/ROM problem
0260 Memory copy PCB 1 communication problem
0350 Mailbox communication problem
0370 Communication microcomputer problem
0380 Hard disk problem
0390 DIMM problem
1040 Optical system problem (AGC)
2100 Drive motor problem / Paper conveying motor problem
2200 Paper feed motor problem
2300 Large paper deck right lift motor problem
2310 Large paper deck left lift motor problem
2420 Upper lift motor problem
2430 Lower lift motor problem
6500 Broken fixing unit thermistor wire
7200 Broken drum thermistor wire
7210 Shorted drum thermistor
7220 Broken drum heater wire

KyoceraMita 6330/7530

Код ошибки Описание
1060 Large paper deck left lift motor problem
2550 Drive motor problem
7520 Shorted drum thermistor
7530 Broken drum thermistor wire

Ошибки финишеров

Код ошибки Описание
8010 Finisher paper conveying motor problem
8030 Finisher (upper) paper conveying belt problem
8140 Finisher tray elevation motor problem /Main tray problem
8170 Finisher front side registration motor problem
8180 Finisher rear side registration motor problem
Finisher rear jogger motor problem (для 4230/5230)
8190 Finisher trailing edge registration motor problem
8210 Finisher stapler motor problem
8220 Finisher rear stapler problem
8300 Document finisher centerfold unit communication problem
8310 Document finisher centerfold unit side registration guide problem
8320 Document finisher centerfold unit centering plate problem
8330 Document finisher centerfold blade problem

Ошибки финишеров KM-2530/3530/3035/4035/5035

Код ошибки Описание
8300 Booklet stitcher paper ejection motor problem
8310 Booklet stitcher elevation motor problem
8320 Booklet stitcher rear jog motor problem
8330 Booklet stitcher front jog motor problem
8340 Booklet stitcher staple motor problem
8350 Booklet stitcher batch processing motor problem
8360 Booklet stitcher stapler shift motor problem
8370 Booklet stitcher paddle motor problem
8380 Booklet stitcher folding problem
8390 Booklet stitcher backup RAM data problem
8400 Booklet stitcher incorrect type problem
8410 Booklet stitcher punch motor problem
8420 Booklet stitcher shift motor problem
8430 Booklet stitcher punch communication problem
8440 Booklet stitcher punch sensor problem
8450 Booklet stitcher side punch sensor problem
8460 Booklet stitcher punch backup RAM data problem
8470 Booklet stitcher punch dust sensor problem
8480 Booklet stitcher broken punch power source wire problem
8500 Mailbox drive motor problem

Ошибки финишера KM-6230

Код ошибки Описание
8180 Finisher rear jogger motor problem
8310 Booklet stitcher paper ejection motor problem
8320 Booklet stitcher elevation motor problem
8330 Booklet stitcher jog motor problem
8340 Booklet stitcher staple motor problem
8350 Booklet stitcher stapler unit shift motor problem
8360 Booklet stitcher stack level detection sensor problem
8370 Booklet stitcher punch motor problem
8380 Booklet stitcher punch shift motor problem
8390 Booklet stitcher swing motor problem
8400 Booklet stitcher backup RAM data problem
8410 Booklet stitcher punch unit backup RAM data problem
8420 Booklet stitcher positioning plate motor problem
8430 Booklet stitcher folding motor problem
8440 Booklet stitcher guide motor problem
8450 Booklet stitcher jog motor problem
8460 Booklet stitcher rear staple motor problem
8470 Booklet stitcher front staple motor problem
8480 Booklet stitcher thrust motor problem
8490 Booklet stitcher communication error

Ошибки финишеров KM-6330/7530/6030/8030

Код ошибки Описание
8000 Document finisher incorrect type problem (для 6330/7530)
8020 Finisher punch motor problem
8040 Finisher lower paper conveying belt problem
8150 Finisher multi job tray problem
8170 Front upper side-registration guide problem
8180 Finisher rear upper side-registration guide problem
8190 Finisher lower side-registration guide problem
8220 Finisher front clincher problem
8230 Finisher rear stapler problem
8240 Finisher rear clincher problem
Источник
  • Code: 0030
  • Description: FAX control PWB system error
    Processing with the fax software was disabled due to a hardware problem.
  • Causes: Defective FAX control PWB.
  • Remedy: Replace the FAX control PWB.
  • Code: 0070
  • Description: FAX control PWB incompatible detection Error
    Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.
  • Causes: Defective fax software. Defective FAX control PWB.
  • Remedy: Defective fax software. Install the fax software.
    Defective FAX control PWB. Replace the FAX control PWB.
  • Code: 0100
  • Description: Backup memory device error
  • Causes: Defective flash memory. Defective control PWB. Defective flash memory. Defective control PWB.
  • Remedy: Replace the control PWB.
  • Code: 0120
  • Description: MAC address data error
  • Causes: Defective flash memory.
  • Remedy: Replace the control PWB.
  • Code: 0130
  • Description: Backup memory read/write error
  • Causes: Defective flash memory. Defective control PWB
  • Remedy: Replace the control PWB.
  • Code: 0140
  • Description: Backup memory data error
  • Causes: Defective flash memory. Defective control PWB.
  • Remedy: Replace the control PWB.
  • Code: 0150
  • Description: Control PWB EEPROM error
    Detecting control PWB EEPROM (U17) communication error.
  • Causes: Improper installation control PWB EEPROM (U17). Defective control PWB.
  • Remedy: Improper installation control PWB EEPROM (U17). Check the installation of the EEPROM (U17) and remedy if necessary.
    Defective control PWB. Replace the control PWB.
    Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
  • Code: 0170
  • Description: Billing counting error
  • Causes: Defective control PWB. Data damage of control PWB EEPROM (U17).
  • Remedy: Defective control PWB. Replace the control PWB.
    Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
  • Code: 0180
  • Description: Machine number mismatch
    Machine number of main and engine does not match.
  • Causes: The main PWB or the engine PWB were exchanged. Data damage of control PWB EEPROM (U17).
  • Remedy: The main PWB or the engine PWB were exchanged. U004 Setting the machine number.
    Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
  • Code: 0420
  • Description: Paper feeder communication error
    Communication error between control PWB and optional paper feeder.
  • Causes: Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF mainPWB.
  • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
    Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective control PWB. Replace the control PWB.
    Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
    Defective PF mainPWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 0830
  • Description: FAX control PWB flash program area checksum error
    A checksum error occurred with the program of the FAX control PWB.
  • Causes: Defective fax software. Defective FAX control PWB.
  • Remedy: Defective fax software. Install the fax software.
    Defective FAX control PWB. Replace the FAX control PWB.
  • Code: 0840
  • Description: Faults of RTC
    The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.
  • Causes: Defective control PWB. The battery is disconnected from the control PWB.
  • Remedy: Defective control PWB. Replace the control PWB.
    The battery is disconnected from the control PWB. Check visually and remedy if necessary.
  • Code: 0870
  • Description: FAX control PWB to control PWB high capacity data transfer problem
    High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.
  • Causes: Improper installation FAX control PWB. Defective FAX control PWB or control PWB.
  • Remedy: Improper installation FAX control PWB. Reinstall the FAX control PWB.
    Defective FAX control PWB or control PWB. Replace the FAX control PWB or control PWB and check for correct operation..
  • Code: 0920
  • Description: Fax file system error
    The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.
  • Causes: Defective FAX control PWB.
  • Remedy: Defective FAX control PWB. Replace the FAX control PWB.
  • Code: 2000
  • Description: Main motor error
    The main motor ready input is not given for 2 s during the main motor is ON.
  • Causes: Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB.
  • Remedy: Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
    Defective main motor. Replace the main motor.
    Defective control PWB. Replace the control PWB.
  • Code: 2610
  • Description: PF paper feed motor error (paper feeder)
    The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON.
  • Causes: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.
  • Remedy: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
    Defective PF paper feed motor drive transmission system. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
    Defective PF main motor. Replace the PF main motor.
    Defective control PWB. Replace the control PWB.
  • Code: 2620
  • Description: PF paper feed motor error (Paper feeder)
    The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON.
  • Causes: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.
  • Remedy: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
    Defective PF paper feed motor drive transmission system. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
    Defective PF main motor. Replace the PF main motor (Refer to the service manual for the paper feeder).
    Defective control PWB. Replace the control PWB.
  • Code: 3100
  • Description: ISU home position errorr.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
    Defective home position sensor. Replace the home position sensor.
    Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective ISU motor. Replace the ISU motor.
  • Code: 3200
  • Description: Exposure lamp error
    The exposure lamp is not turned on.
  • Causes: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Defective exposure lamp.sensor. Defective LED drive PWB. Defective control PWB.
  • Remedy: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
    Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective exposure lamp. Replace the exposure lamp.
    Defective LED drive PWB. Replace the LED drive PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3300
  • Description: AGC error
    After AGC, correct input is not obtained at CCD.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp.sensor. Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective exposure lamp. Replace the exposure lamp.
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3500
  • Description: CPU — ASIC (CCD PWB) communication error
    An error code is detected.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 4000
  • Description: Polygon motor (laser scanner unit) error
    The polygon motor ready input is not given for 6 s during the polygon motor is ON.
  • Causes: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.
  • Remedy: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4200
  • Description: BD error (laser scanner unit) error
  • Causes: BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.
  • Remedy: BD sensor does not detect laser beam due to condensation on the polygon mirror. Turn machine power off for at least 30 minutes, then turn machine on again. If not cured, replace the laser scanner unit.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4700
  • Description: VIDEO ASIC device error
    Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
  • Causes: Defective connector cable or poor contact in the connector. Defective control PWB.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable.
    Defective control PWB. Replace the control PWB.
  • Code: 3200
  • Description: Exposure lamp error
    The exposure lamp is not turned on.
  • Causes: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Defective exposure lamp.sensor. Defective LED drive PWB. Defective control PWB.
  • Remedy: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
    Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective exposure lamp. Replace the exposure lamp.
    Defective LED drive PWB. Replace the LED drive PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3300
  • Description: AGC error
    After AGC, correct input is not obtained at CCD.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp.sensor. Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective exposure lamp. Replace the exposure lamp.
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3500
  • Description: CPU — ASIC (CCD PWB) communication error
    An error code is detected.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 4000
  • Description: Polygon motor (laser scanner unit) error
    The polygon motor ready input is not given for 6 s during the polygon motor is ON.
  • Causes: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.
  • Remedy: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4200
  • Description: BD error (laser scanner unit) error
  • Causes: BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.
  • Remedy: BD sensor does not detect laser beam due to condensation on the polygon mirror. Turn machine power off for at least 30 minutes, then turn machine on again. If not cured, replace the laser scanner unit.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4700
  • Description: VIDEO ASIC device error
    Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
  • Causes: Defective connector cable or poor contact in the connector. Defective control PWB.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable.
    Defective control PWB. Replace the control PWB.
  • Code: 3200
  • Description: Exposure lamp error
    The exposure lamp is not turned on.
  • Causes: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Defective exposure lamp.sensor. Defective LED drive PWB. Defective control PWB.
  • Remedy: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
    Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective exposure lamp. Replace the exposure lamp.
    Defective LED drive PWB. Replace the LED drive PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3300
  • Description: AGC error
    After AGC, correct input is not obtained at CCD.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp.sensor. Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective exposure lamp. Replace the exposure lamp.
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 3500
  • Description: CPU — ASIC (CCD PWB) communication error
    An error code is detected.
  • Causes: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.
  • Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
    Defective CCD PWB. Replace the CCD PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 4000
  • Description: Polygon motor (laser scanner unit) error
    The polygon motor ready input is not given for 6 s during the polygon motor is ON.
  • Causes: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.
  • Remedy: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4200
  • Description: BD error (laser scanner unit) error
  • Causes: BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.
  • Remedy: BD sensor does not detect laser beam due to condensation on the polygon mirror. Turn machine power off for at least 30 minutes, then turn machine on again. If not cured, replace the laser scanner unit.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective control PWB. Replace the control PWB.
  • Code: 4700
  • Description: VIDEO ASIC device error
    Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
  • Causes: Defective connector cable or poor contact in the connector. Defective control PWB.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable.
    Defective control PWB. Replace the control PWB.
  • Code: 6000
  • Description: Broken Fuser heater wire
    The fuser temperature does not rise after the Fuser heater has been turned on.
  • Causes: Poor contact in the fuser thermistor connector terminals. Poor contact in the Fuser heater connector terminals. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire.
  • Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector.
    Poor contact in the Fuser heater connector terminals. Reinsert the connector.
    Fuser thermistor installed incorrectly. Replace the fuser unit.
    Fuser thermal cutout triggered. Replace the fuser unit.
    Fuser heater installed incorrectly. Replace the fuser unit.
    Broken Fuser heater wire. Replace the fuser unit.
  • Code: 6020
  • Description: Abnormally high fuser thermistor temperature
    Fuser thermistor detects abnormally temperature. When the temperature of a fuser thermistor detects 195 °C or more at the time of heater OFF and 155 °C or more.
  • Causes: Shorted fuser thermistor. Defective control PWB.
  • Remedy: Shorted fuser thermistor. Replace the fuser unit.
    Defective control PWB. Replace the control PWB.
  • Code: 6030
  • Description: Broken fuser thermistor wire
    Input from fuser thermistor is 0 (A/D value).
  • Causes: Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire.
  • Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector.
    Broken fuser thermistor wire. Replace the fuser unit.
    Fuser thermistor installed incorrectly. Replace the fuser unit.
    Fuser thermal cutout triggered. Replace the fuser unit.
    Fuser heater installed incorrectly. Replace the fuser unit.
    Broken Fuser heater wire. Replace the fuser unit.
  • Code: 6400
  • Description: Zero cross signal error
    The zero cross signal does not reach the control PWB for specified time.
  • Causes: Defective harness between high voltage PWB (CN202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (CN201). Defective power source PWB. Defective control PWB.
  • Remedy: Defective harness between high voltage PWB (CN202) and control PWB (YC23), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective connection between power source PWB (YC103) and high voltage PWB (CN201). Reinsert the connector.
    Defective power source PWB. Replace the power source PWB.
    Defective control PWB. Replace the control PWB.
  • Code: 7990
  • Description: Waste toner full
    The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.
  • Causes: Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Defective control PWB.
  • Remedy: Waste toner reservoir (drum unit) is full. Turn the power switch off/on to restart the machine. If the error is not resolved, replace the drum unit.
    Defective waste toner sensor. Replace the waste toner sensor.
    Defective control PWB. Replace the control PWB.
  • Code: F000
  • Description: Control PWB — Operation panel PWB communication error
  • Causes: Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. motor is ON. Defective operation panel PWB. Defective control PWB.
  • Remedy: Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
    Defective operation panel PWB. Replace the operation panel PWB.
    Defective control PWB. Replace the control PWB.
  • Code: F020
  • Description: Control PWB RAM checksum error
  • Causes: Defective main memory (RAM) on the control PWB. Defective expanded memory (DIMM).
  • Remedy: Defective main memory (RAM) on the control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
    Defective expanded memory (DIMM). Replace the expanded memory (DIMM).
  • Code: F040
  • Description: Control PWB engine communication error
    A communication error is detected.
  • Causes: Defective control PWB.
  • Remedy: Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
  • Code: F041
  • Description: Control PWB — scanner PWB communication error
    A communication error is detected.
  • Causes: Defective control PWB or scanner PWB.
  • Remedy: Defective control PWB or scanner PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB or scanner PWB.
  • Code: F050
  • Description: Control PWB engine checksum error
  • Causes: Some error may have occurred when downloading the firmware of the control PWB. Defective control PWB.
  • Remedy: Some error may have occurred when downloading the firmware of the control PWB. Download the firmware of the control PWB again.
    Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
  • Code: F186
  • Description: Control PWB video data control error
  • Causes: Defective control PWB.
  • Remedy: Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
Источник

C0030
Системная ошибка в управлении факсом
Обработка при помощи программного обеспечения факса была отключена из за проблем с оборудованием
Неисправность в системе управления факсом PWB
Заменить систему управления факсом PWB

C0070
Обнаружена несовместимость платы управления PWB
Обнаружена несовместимость при первичной инициализации системы управления факсом PWB. Никакие команды связи не проходят.
Дефект программного обеспечения факса
Установить программное обеспечение для факса

C0100
Ошибка при резервном копировании памяти устройства

Неисправна флеш память
Заменить плату управления PWB

C0120
Ошибка данных MAC адреса

Неисправность в плате управления PWB
Заменить плату управления PWB

C0130
Ошибка чтения/записи при резервном копировании

Неисправна флеш память
Заменить плату управления PWB

C0140
Ошибка при резервном копировании данных

Неисправна флеш память
Заменить плату управления PWB

C0150
Ошибка EEPROM платы управления PWB
Обнаружена ошибка связи PWB EEPROM (U17)
Неправильная установка PWB EEPROM (U17)
Проверить установку EEPROM (U17) и при необходимости исправить

C0170
Ошибка счетчика

1. Неисправность control PWB.

2. Повреждения данных PWB EEPROM (U17)

1. Заменить плату управления PWB.

2. Обратиться в сервис обслуживания

C0180
Номер аппарата не совпадает
Основной номер и номер двигателя не совпадают
1. Основная PWB или PWB двигателя была заменена.

2. Повреждения данных PWB EEPROM (U17)

1. U004 Задать номер.

2. Обратиться в сервис обслуживания

C0420
Ошибка связи с системой подачи бумаги
Ошибка коммуникации между платой PWB  и дополнительным устройством подачи бумаги
1. Неправильная установка устройства подачи бумаги

2. Повреждение провода между платой PWB (YC30) и интерфесным разъемом устройства подачи, либо разъем подключен неправильно.

3. Неисправен кабель между PF основной PWB и подачей бумаги, либо разъем не вставлен. Плата PF неисправна.

4. Неисправность control PWB

1. Еще раз внимательно прочитайте инструкцию по установке.

2. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

3. Убедитесь, что разъем подключен, а кабель не поврежден.Заменить печатную плату.

4. Заменить плату управления PWB.

C0830
Ошибка контрольной суммы прошивки FAX control PWB
Произошла ошибка контрольной суммы программы управления FAX control PWB
1. Дефект программного обеспечения факса.

2. Неисправность в системе управления факсом PWB

1. Установить программное обеспечение для факса.

2. Заменить плату управления факсом PWB

C0840
Неисправность RTС
Расхождение во времени между RTC  и текущим пять и более лет.
1. Неисправность control PWB

2. Отсоединена батарея.

1. Заменить плату управления PWB.

2. Визуально проверить и при необходимости исправить.

C0870
Проблема передачи данных большой емкости между FAX control PWB и control PWB
Не выполняется передача данных между FAX control PWB и control PWB, даже при повторе через заданный промежуток
 Неправильная установка  FAX control PWB

Переставить FAX control PWB

C0920
Ошибка файловой системы факса
Резервное копирование данных не производится по причине ошибки файловой системы флеш-памяти
Неисправность в системе управления факсом PWB
Заменить плату управления факсом PWB

C2000
Ошибка главного двигателя
Главный двигатель не выходит на готовность в течение 2 секунд после включения
1. Неисправен кабель между основным двигателем (CN1) и платой PWB (YC17) или разъем вставлен неправильно.

2. Неисправен привод основного двигателя.

3. Неисправен двигатель.

4. Неисправность control PWB

1. Вставьте разъем. Проверьте целостность кабеля.

2. Проверьте плавность вращения роликов и шестерней. При необходимости смажьте. Убедитесь в отсутсвии разрывов передач.

3. Заменить.

4. Заменить.

C2610
Ошибка дигателя устройства подачи бумаги
Двигатель устройства подачи бумаги лотка 2 не выходит на готовность более чем через 2 секунды после включения.
Неисправность кабеля между двигателем устройства подачи бумаги и control PWB (YC4).
 Вставьте разъем. Проверьте целостность кабеля (Обратитесь к инструкции)

C2620
Ошибка дигателя устройства подачи бумаги
Двигатель устройства подачи бумаги лотка 3 не выходит на готовность более чем через 2 секунды после включения.
Неисправность кабеля между двигателем устройства подачи бумаги и control PWB (YC4).
Вставьте разъем. Проверьте целостность кабеля (Обратитесь к инструкции)

C3100
Ошибка исходного положения ISU

1. Неисправность FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность FFC между control PWB (YC6) и сканера WPB (YC103) или неправильная установка FCC.

3. Неисправность датчика исходного положения.

4. Неисправность кабеля между двигателем ISU и сканером PWB (YC104) или разъем вставлен неправильно.

1. Заменить блок сканера ISU

2. Переставить FFC. Проверить на разрыв, при необходимости заменить.

3. Заменить датчик.

4. Вставьте разъем. Проверьте целостность кабеля.

C3200
Ошибка лампы экспозиции
Лампа экспозиции не включается
1. Повреждения FFC между сканером PWB (YC103) и control PWB (YC6), либо некорректная установка FFC.

2. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

3. Неисправен кабель между CCD PWB (YC3) и LED приводом PWB (YC1) либо разъем не подключен.

4. Неисправен кабель между LED приводом PWB (YC2) и лампой экспонирования.

5. Лампа экспонирования вышла из строя.

6. Неисправен светодиодный привод.

1. Переустановите FFC. Проверьте целостность, при необходимости замените.

2. Заменить блок сканера.

3. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

4. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

5. Заменить лампу.

6. Заменить привод.

C3300
Ошибка AGC

1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Лампа экспонирования вышла из строя.

3. Неисправность CCD PWB

4. Неисправность control PWB

1. Заменить блок сканера.

2. Заменить лампу.

3. Заменить CCD PWB

4. Заменить control PWB

C3500
Ошибка связи CPU — ASIC (CCD PWB)
Обнаружен код ошибки
1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность CCD PWB.

3. Неисправность control PWB

1. Заменить блок сканера (ISU).

2. Заменить CCD PWB

3. Заменить control PWB

C4000
Ошибка полигон-мотора (блока лазерного сканера)
Полигон-мотор не выходит на готовность после 6 секунд после включения.
1. Поврежден кабель между полигон-мотором и control PWB (YC10) или разъем не вставлен.

2. Неисправен блок лазерного сканера.

3. Неисправность control PWB

1. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

2. Заменить блок сканера.

3. Заменить control PWB

C4200
Ошибка BD  (блока лазерного сканера)

1. BD датчик не обнаруживает лазерный луч из-за скопления конденсата на зеркале.

2. Неисправен блок лазерного сканера.

1. Выключите питание машины минимум на 30 минут, затем снова включите, если это не помогает необходимо менять блок сканера.

2. Заменить блок сканера.

C6000
Выход из строя термо-элемента (фьюзера)
Температура фьюзера не поднимается после включения устройства.
1. Плохой контакт клемм термистора фьюзера.

2. Плохой контакт в местах подключения нагревателя термоблока.

3. Термисторы фьюзера установлены неправильно.

4 . Срабатывает термореле

5. Нагреватель фьюзера установлен неправильно

6. Выход из строя термо-элемента

1. Проверьте контакты.

2. Проверьте контакты.

3. Заменить блок закрепления

4. Заменить блок закрепления

5. Заменить блок закрепления

6. Заменить блок закрепления

C6020
Слишком высокая температура фьюзера
Термистор фьюзера обнаружил аномально высокую температуру.
Пробой термистора фьюзера
Заменить блок закрепления

C6030
Поврежден шлейф термистора термоэлемента
Значени на входе термистора равно 0
1. Плохой контакт в клеммах термистора.

2. Неисправен шлейф термистора

3. Термистор установлен некорректно

4. Срабатывает термореле

Проверить контакты

Заменить блок закрепления

C6400
Ошибка пересечения нуля
Сигнал пересечения нуля не достигает контрольной платы за указанное время
1. Неисправен кабель между PWB высокого напряжения(YC202) и control PWB (YC23) или разъем не вставлен

2. Дефект соединения между источником питания PWB (YC103) и PWB высокого напряжения (YC201)

3. Неисправен источник питания PWB

4. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Переподключите коннектор

3. Заменить источник питания

4. Заменить control PWB

C7990
Бункер отработки переполнен
Датчик тонера обнаружил, что бункер для отработки переполнен
1. Бункер отработки драм-юнита переполнен.

2. Неисправен датчик отработки

3. Неисправность control PWB

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла замените драм-юнит.

2. Замените датчик.

3. Заменить control PWB

4. Очистите драм юнит (инструкция по очистке бункера отработанного тонера)

F000
Ошибка связи control PWB — панель управления PWB

1. Неисправность соединения панели управления PWB (YC1) и control PWB (YC7).

2. Неисправность панели управления

3. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Замените панель.

3. Заменить control PWB

F020
Ошибка контрольной суммы RAM control PWB

1. Неисправность основной микросхемы памяти (ОЗУ) на главной плате управления PWB

2. Неисправность платы расширения памяти (DIMM)

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

2. Замените плату расширения (DIMM)

F040
Ошибка связи control PWB двигателя
Обнаружена ошибка связи
Неисправность control PWB
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F041
Ошибка связи между гланой платой управления и платой управления сканером
Обнаружена ошибка связи
Неисправна главная плата управления или управления сканером
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB или scanner PWB

F050
Ошибка контрольной суммы платы управления двигателем

1. Такие ошибки могут происходить при обновлении прошивки control PWB

2. Неисправность control PWB

1. Скачайте прошивку снова

2. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F186
Ошибка управления видеоданными главной панели управления

Неисправность control PWB
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

Источник

Понравилась статья? Поделить с друзьями:

Не пропустите эти материалы по теме:

  • Яндекс еда ошибка привязки карты
  • Куосера 2335dn ошибки
  • Куосера 2335 индикация ошибок
  • Куосера 2235 сброс ошибки тонера
  • Куосера 2235 неоригинальный картридж сброс ошибки

    • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии