Куосера 3055 ошибка 7410 - Не ошибается лишь тот, кто ничего не делает!

Модератор: vetal

Всем привет. Данный аппарат выдает ошибку 7410. Я понимаю что эта ошибка говорит о плохом контакте на драм, но при включении принтера с открытой крышкой, аппарат выходит в готовность, далее закрываем крышку, и он печатает без проблем, без каких либо дефектов. Принтак продувал, чистил, ничего не помогло, Ставлю другой драм с другой проявкой, та же ошибка, поставил третий драм с другой проявкой выдал ошибку 0180, со старым драмом так же C7410

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

kvg » Чт июн 20, 2019 8:56 am

А стандартное решение проблемы не помогает?

Выключите принтер. Откройте левую дверь и нажмите на барабан, пока он не защелкнется на месте. Снова включите принтер, аппарат войдет в готовность.

kvg

Администратор сайта и форума

Сайт
Персональный альбом

Andreyak777 » Чт июн 20, 2019 1:08 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Andreyak777 » Чт июн 20, 2019 1:12 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Andreyak777 » Чт июн 20, 2019 2:47 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

pc-porta » Чт июн 20, 2019 3:24 pm

Andreyak777 писал(а):Если была бы проблема в контактах, грязь там и все такое, почему он тогда нормально печатает когда загружается с открытой крышкой??

люфтит у Вас драм (шатает его) при закрывании крышки …

Драм совместимка или оригинал ?
Контакты чють подвытянуть в драме или принтаке … для лучшего и надёжного контакта :))

pc-porta

Тонерный автобот

Персональный альбом

dviz » Чт июн 20, 2019 7:14 pm

Andreyak777 писал(а):DK3130 изначально стоял, с ним все работало

Оно конечно, хорошо, но это ж не родной — может глюк какой — там в нём плата сопряжения маленькая с микрухой(кто-то на форуме уже писал, что они иногда дохнут) и датчик регистрации лишний (можно попробовать его отключить).
Плюс ещё по 0180 — проверить в U004 не сбойнули ли серийные номера.

dviz

Эксперт по тонеру

Персональный альбом

dviz » Пт июн 21, 2019 10:54 am

Да, в 3130 стоит датчик регистрации, в 3100 — нет, и для m3040 — не нужен.

Надо бы для начала узнать с каких аппаратов и какие модели драмов ставились..

За это сообщение автора dviz поблагодарил:: admdep33

dviz

Эксперт по тонеру

Персональный альбом

dviz » Пт июн 21, 2019 2:57 pm

Только что была возможность поэксперимениировать.

Вытащил из включенного m3040dn dk-3100, установил dk-3130 — работает. Выключил-включил — ошибка c7410. Вернул dk-3100 обратно — всё норм.

В fs-4100 вместо dk-3130 установил dk-3100 — ошибка замятия бумаги — ожидаемо — ведь в dk-3100 нет датчика регистрации и в аппарате нет..

За это сообщение автора dviz поблагодарил:: Andreyak777

dviz

Эксперт по тонеру

Персональный альбом

dviz » Пт июн 21, 2019 3:51 pm

Проблема в данном случае не в самом наличии или отсутствии датчика, а в том что используется не родной драм..

В аппаратах со скоростью 40-45 стр/мин — fs 2100, m3040, p3045 и т.п. — два датчика регистрации в самом аппарате, поэтому датчик в драме не требуется. Во всех остальных — в самом аппарате один датчик и один в драме.

Тут поправлюсь — в fs2100, m3040, p3045 не два, а только один датчик регистрации — до валов регистрации, а в остальных аппаратах два: один — после валов регистрации, и один — в драме.

Последний раз редактировалось dviz Сб июн 22, 2019 3:42 pm, всего редактировалось 1 раз.

За это сообщение автора dviz поблагодарил:: admdep33

dviz

Эксперт по тонеру

Персональный альбом

Kyocera FS-1120d индикатор «Нет бумаги»

vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

11

15142

СТРОНЦИЙ

Вт ноя 02, 2021 2:24 pm
[SCANNER ERROR] Lamp Error Kyocera FS-1016

мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

3

6645

Усатый Полосатый

Вс окт 28, 2018 11:08 pm
Kyocera 1035 «бледная» печать

srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

2

13949

srMax

Пт янв 23, 2015 2:49 pm
Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

manik.76 в форуме Принтеры, МФУ, копиры формата A3

3

9650

dviz

Пн фев 20, 2017 1:35 pm
Kyocera Ecosys M2635dn «поворот» изображения

Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

10

6103

MatrixAgent

Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 80

Источник

Правила форума
Картинки и фотографии (если они нужны в сообщении) надо загружать только как вложения к своему сообщению (через кнопку Добавить файлы). Тогда картинки будут автоматически отображаться в сообщении.

lamac0: Сообщения: 4; Стаж: 7 месяцев

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

lamac0 » 12 окт 2022, 08:49

Всем по привету, при включении данный аппарат говорит обратиться к сервисникам с кодом ошибки 7410:0035148, понимая, что дело где-то в драме зарыто полез копать гуглы, там сказали, что бывает крякает плата на драме, нашел донора, подкинул плату и результата нет, НО! если выдеруть питалово, открыть крышку переднюю, подать питалово, то он работает как ни в чем не бывало, до ребута

dviz: Сообщения: 204; Стаж: 1 год 5 месяцев; Откуда: Ярославль; Благодарил (а): 15 раз; Поблагодарили: 25 раз; Репутация:

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

dviz » 15 окт 2022, 03:41

Если есть донор — то ставьте донора и проверяйте работоспособность. Только хорошо бы конечно быть уверенным, что донор действительно рабочий. Если с открытой крышкой включается, то вероятно он при инициализации не проверяет работоспособность всех компонентов драма, а с закрытой проверяет и что-то его не устраивает — проверьте всё что там подключено к этой платке — датчик тонера, движок подмеса, засветку фотика.

4 Ответы

486 Просмотры

Последнее сообщение

22 окт 2022, 21:22
2 Ответы

538 Просмотры

Последнее сообщение

03 мар 2023, 02:18
1 Ответы

154 Просмотры

Последнее сообщение

19 сен 2022, 07:48
21 Ответы

186 Просмотры

Последнее сообщение

30 май 2023, 23:34
0 Ответы

128 Просмотры

Последнее сообщение

13 дек 2022, 19:30

Источник

Модератор: vetal

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

kvg » Чт июн 20, 2019 8:56 am

А стандартное решение проблемы не помогает?

kvg

Администратор сайта и форума

Сайт
Персональный альбом

Andreyak777 » Чт июн 20, 2019 1:08 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Andreyak777 » Чт июн 20, 2019 1:12 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Andreyak777 » Чт июн 20, 2019 2:47 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

pc-porta » Чт июн 20, 2019 3:24 pm

Andreyak777 писал(а):Если была бы проблема в контактах, грязь там и все такое, почему он тогда нормально печатает когда загружается с открытой крышкой??

люфтит у Вас драм (шатает его) при закрывании крышки …

pc-porta

Форумный оракул

Персональный альбом

dviz » Чт июн 20, 2019 7:14 pm

Andreyak777 писал(а):DK3130 изначально стоял, с ним все работало

dviz

Блуждающий заряд

Персональный альбом

dviz » Пт июн 21, 2019 10:54 am

Да, в 3130 стоит датчик регистрации, в 3100 — нет, и для m3040 — не нужен.

Надо бы для начала узнать с каких аппаратов и какие модели драмов ставились..

dviz

Блуждающий заряд

Персональный альбом

dviz » Пт июн 21, 2019 2:57 pm

Только что была возможность поэксперимениировать.

За это сообщение автора dviz поблагодарил:: Andreyak777

dviz

Блуждающий заряд

Персональный альбом

dviz » Пт июн 21, 2019 3:51 pm

Проблема в данном случае не в самом наличии или отсутствии датчика, а в том что используется не родной драм..

Последний раз редактировалось dviz Сб июн 22, 2019 3:42 pm, всего редактировалось 1 раз.

dviz

Блуждающий заряд

Персональный альбом

[SCANNER ERROR] Lamp Error Kyocera FS-1016

мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

3

6436

Усатый Полосатый

Вс окт 28, 2018 11:08 pm
Kyocera 1035 «бледная» печать

srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

2

13544

srMax

Пт янв 23, 2015 2:49 pm
Kyocera FS-1120d индикатор «Нет бумаги»

vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

11

14587

СТРОНЦИЙ

Вт ноя 02, 2021 2:24 pm
Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

manik.76 в форуме Принтеры, МФУ, копиры формата A3

3

9189

dviz

Пн фев 20, 2017 1:35 pm
Kyocera Ecosys M2635dn «поворот» изображения

Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

10

5752

MatrixAgent

Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 102

Code: 0100
Description: Backup memory device error
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0120
Description: MAC address data error For data in which the MAC address is invalid.
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0130
Description: Backup memory read/write error (main PWB)
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0140
Description: Backup memory data error (main PWB)
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0150
Description: Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error.
Remedy: Improper installation engine PWB EEPROM. Check the installation of the EEPROM and remedy if necessary.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 0160
Description: Backup memory data error (engine PWB)
Remedy: Defective EEPROM. Replace the engine PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 0170
Description: Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.
Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.

Code: 0190
Description: Backup memory device error (engine PWB)
Remedy: Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 0800
Description: Image processing error JAM010x is detected twice.
Remedy: Defective main PWB. Replace the main PWB and check for correct operations page 1-5-22).

Code: 0840
Description: Faults of RTC Unable to communicate with the RTC device normally. The RTC data is mismatched due to dead battery or shortcircuit with the metal part.
Remedy: Other RTC device failure due to dead battery or short-circuit with the metal part. Restart the main unit and set the correct time from the operation panel. Repair it if the battery comes off from the main PWB.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 1010
Description: Lift motor error (60/55/50 ppm model only) After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected five times successively.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor and engine PWB (YC13)
Defective drive transmission system of the lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective lift motor. Replace the lift motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1020
Description: PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 1.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1030
Description: PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 2.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1040
Description: PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 3 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 3.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1050
Description: PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 4 and PF main PWB (YC7)
Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor. Replace the PF lift motor 4.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1140
Description: BPF lift motor upward error (Bulk paper feeder) BPF lift maximum sensor does not turn on. The lock signal of the motor is detected continuously three times.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective BPF lift motor. Replace the BPF lift motor.
Defective BPF main PWB. Replace the BPF main PWB (Refer to the service manual for the paper feeder).

Code: 1150
Description: BPF lift motor downward error (Bulk paper feeder) BPF lift minimum sensor does not turn on. The lock signal of the motor is detected continuously three times. When detecting an overcurrent detection signal.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective BPF lift motor. Replace the BPF lift motor.
Defective BPF main PWB. Replace the BPF main PWB (Refer to the service manual for the paper feeder).

Code: 1800
Description: Paper feeder 1 communication error A communication error is detected 10 times in succession.
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1810
Description: Paper feeder 2 communication error A communication error is detected 10 times in succession.
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1820
Description: Paper feeder 3 communication error A communication error is detected 10 times in succession.
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1830
Description: Paper feeder 4 communication error A communication error is detected 10 times in succession.
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1900
Description: Paper feeder 1/BPF paper feeder EEPROM error When writing the data, the write data and the read data is not in agreement.
Remedy: Defective PF main PWB. Replace the PF main PWB or the BPF main PWB.
Device damage of EEPROM. Replace the PF main PWB or the BPF main PWB.

Code: 1910
Description: Paper feeder 2 EEPROM error When writing the data, the write data and the read data is not in agreement.
Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1920
Description: Paper feeder 3 EEPROM error When writing the data, the write data and the read data is not in agreement.
Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1930
Description: Paper feeder 4 EEPROM error When writing the data, the write data and the read data is not in agreement.
Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2000
Description: Main motor drive error The main motor is not stabilized within 2 s after driving starts.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective main motor. Replace the main motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2010
Description: Main motor steady-state error Stable OFF is detected for 2 s continuously after main motor stabilized.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective main motor. Replace the main motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2200
Description: Drum motor drive error (60/55/50 ppm model only) The drum motor is not stabilized within 2 s after driving starts.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective drum motor. Replace the drum motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2210
Description: Drum motor steady-state error (60/55/50 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective drum motor. Replace the drum motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2330
Description: Fuser pressure release motor error (Over-current) The over-current detection signal of the motor is detected continuously twenty times.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC3) and engine PWB(YC2)
Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser pressure release motor. Replace the fuser pressure release motor.
Defective PWB. Replace the relay-L PWB or engine PWB.

Code: 2340
Description: Fuser pressure release motor error (Timeout) The position detection sensor is not detected continuously for 30 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC1) and engine PWB(YC2)
Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser pressure release motor. Replace the fuser pressure release motor.
Defective PWB. Replace the relay-L PWB or engine PWB.

Code: 2600
Description: PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 1 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 1.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2610
Description: PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 2 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 2.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2620
Description: PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 3 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 3.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2630
Description: PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 4 and PF main PWB (YC6)
Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF drive motor. Replace the PF drive motor 4.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 4000
Description: Polygon motor synchronization error The polygon motor is not stabilized within 20 s after driving starts.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Polygon motor and engine PWB (YC15)
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4200
Description: BD steady-state error When the value of Register BDSET is 1 after setting Register BDSET as one and passing by BD1 cycle.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB(YC1) and engine PWB (YC16) APC PWB(YC2) and PD PWB(YC1)
Defective PD PWB. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 5100
Description: Chager current error When the current value measured at the time of potential adjustment is less than 20 uA.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Chager unit and high voltage PWB High voltage PWB (YC101) and engine PWB (YC19)
Defective high voltage PWB. Replace the high voltage PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6000
Description: Broken fuser heater wire The detection temperature of fuser thermistor 2 is 100 °C/ 212°F or less after the fuser heater lamp has been turned on continuously for 30 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser heater and power source PWB (YC2) Fuser thermistor and Fuser thermistor connect PWB(YC1 and YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Fuser thermostat triggered. Reinsert the fuser unit.
Broken fuser heater wire. Reinsert the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6020
Description: Abnormally high fuser thermistor 2 temperature The detection temperature of fuser thermistor 2 is higher than 235°C/455°F. In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.
Remedy: Deformed connector pin.
Defective triac.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030
Description: Broken fuser thermistor 2 wire A/D value of the fuser thermistor 2 exceeds 1019 bit continuously for 4 s during warming up.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6120
Description: Abnormally high fuser thermistor 1 temperature The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.
Remedy: Deformed connector pin.
Defective triac.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6130
Description: Broken fuser thermistor 1 wire A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC1) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
Deformed connector pin.
Defective triac.
Defective fuser thermistor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6400
Description: Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 2 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and engine PWB (YC1)
Defective power source PWB or engine PWB. Replace the power source PWB or the engine PWB and check for correct operation.

Code: 7100
Description: Toner sensor error Sensor output value of 930 or more continuously for 5 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7400
Description: Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7410
Description: Drum unit type mismatch error The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective toner sensor. Replace the drum unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7800
Description: Broken external thermistor wire The average of thermistor output value of 93 or less.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
Defective temperature sensor. Replace the operation PWB.

Code: 7810
Description: Short-circuited external thermistor wire The average of thermistor output value of 930 or more.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
Defective temperature sensor. Replace the operation PWB.

Code: 7900
Description: Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
Defective drum unit. Replace the drum unit.

Code: F000
Description: Main PWB — operation PWB communication error
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB(YC1) and engine PWB (YC17)
Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective operation PWB. Replace the operation PWB and check for correct operation.

Code: F000
Description: CF000 will be displayed if * notes progress is carried out for a definite period of time with a Welcome screen.The communication fault between Panel-Main boardsCommunication fault between Panel Core-Main Core Notes 2
Remedy: (1) Check the harness, and the connection state of a connector between Panel<=>Main boards, and perform an operation check. (2) Check contact of a DDR memory (extracting) and perform an operation check. If exchangeable, it will exchange and will perform an operation check. (3) U021 Controller backup initialization is carried out and an operation check is performed. (4) Exchange a Main board and perform an operation check. (5) Exchange a PanelMain board and perform an operation check. (6) It will get, if USBLOG is obtainable, and contact service headquarters. 1. Panel <=> Main IF (Engine PWB Relay) Main PWB: YC2 Engine PWB: YC20,YC30 Panel PWB: YC1 2. DDR memory Main PWB: YS1

Code: F010
Description: Main PWB checksum error
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.

Code: F020
Description: Main PWB RAM checksum error
Remedy: Defective main memory (RAM) in main PWB Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective expended memory (DIMM) Replace the expansion memory (DIMM). Also in the case of the capacity besides specification, it displays.

Code: F040
Description: Main PWB — print engine communication error
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: F050
Description: Print engine ROM checksum error
Remedy: Defective engine PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace engine PWB.

Code: F15X
Description: Abnormality detecting in an authentication device control section
Remedy: (1) Check the harness between authentication device <=>Main boards, and the connection situation of a connector, and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters. 1.Authentication device <=> Main IF Main PWB: YC6 Authentication device: IC card reader etc.

Code: F17X
Description: Abnormality detecting in a printer data control part
Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F18X
Description: Abnormality detecting in a Video control section
Remedy: (1) Check the harness between Engine<=>Main boards, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange an Engine board and perform an operation check. (4) Exchange a Main board and perform an operation check. (5) Get USBLOG and contact service headquarters.

Code: F1DX
Description: Abnormality detecting of the image memory Management Department
Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F21X, F22X, F23X
Description: Abnormality detecting in an image-processing part
Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters.

Code: F24X
Description: Abnormality detecting in the system Management Department
Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters * F248 is the abnormalities of a printer process.In recurring by specific printer data, please give me cooperation at acquisition of capture data and USBLOG.

Code: F25X
Description: Abnormality detecting in a network management department
Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters. * It may occur according to a visitor’s network environment

Code: F26X, F27X, F28X
Description: Abnormality detecting in the system Management Department
Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F29X, F2AX
Description: Abnormality detecting in the system Management Department
Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F2BX, F2CX, F2DX
Description: Abnormality detecting in a network control part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)

Code: F2EX, F2FX, F30X
Description: Abnormality detecting in a network control part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)

Code: F31X, F32X
Description: Abnormality detecting in a network control part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)

Code: F35X
Description: Abnormality detecting in the printing controlling Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F38X
Description: Abnormality detecting in the authentication authorized Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F3AX, F3BX, F3CX
Description: Abnormality detecting in the Entity Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F3DX, F3EX, F3FX
Description: Abnormality detecting in the Entity Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F40X, F41X, F42X
Description: Abnormality detecting in the Entity Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F43X, F44X, F45X
Description: Abnormality detecting in the Entity Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F46X
Description: Abnormality detecting of a printer rendering part
Remedy: (1) Exchange boards and perform an operation check. (2) the acquisition wish of USBLOG — carry out (Depending on the (2) case, it is print capture data acquisition)

Code: F47X
Description: Abnormality detecting of an image editing processing part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F4DX, F4EX
Description: Abnormality detecting in the Entity Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F4FX
Description: Abnormality detecting in the JOB Management Department
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F51X, F52X, F53X
Description: Abnormality detecting in a JOB execution part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F55X, F56X, F57X
Description: Abnormality detecting in a JOB execution part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters

Code: F5FX
Description: Abnormality detecting in a service execution part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F62X
Description: Abnormality detecting in a service execution part
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Code: F63X
Description: Abnormality detecting in a device control section
Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

lamac0: Сообщения: 4; Стаж: 3 месяца

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

lamac0 » 12 окт 2022, 08:49

dviz: Сообщения: 178; Стаж: 1 год 1 месяц; Откуда: Ярославль; Благодарил (а): 11 раз; Поблагодарили: 22 раза; Репутация:

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

dviz » 15 окт 2022, 03:41

4 Ответы

157 Просмотры

Последнее сообщение

22 окт 2022, 21:22
1 Ответы

93 Просмотры

Последнее сообщение

19 сен 2022, 07:48
0 Ответы

53 Просмотры

Последнее сообщение

13 дек 2022, 19:30
13 Ответы

2617 Просмотры

Последнее сообщение

03 фев 2022, 15:54
6 Ответы

2196 Просмотры

Последнее сообщение

02 фев 2022, 11:07

Источник

Dima_NSO писал(а):Вообщем пробема вот в чем, было замятие бумаги я вытащил драм-картридж удалил бумагу и вставил его, но он отпечатал пустой лист бумаги. Я решил, что он просто не ровно встал переустановил и он мне выдал ошибку 7410, затем несколько раз пробывал вытаскивать-устанавливать как с тонером так и без него не помогло, самое забавное что даже без драм-картриджа все равно выдает эту ошибку, как мне ее сбросить ?

как вышел из ситуации и вышел ли вообще?

amag1 писал(а):это ошибка драма
аппарат его не видит
на самом драме есть маленькая плата посмотри все контакты

контакты и платку нашел посмотрел выглядят как новые

Источник

Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки	Описание ошибки	Причина ошибки
0030	FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.	Defective FAX control PWB.
0060	Control PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard	Control PWB
0070	FAX control PWB incompatible detection Error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.	FAX control PWB (The FAX PWB installed will not be the one designed for the machine.
0100	Backup memory device error	EEPROM (Control PWB)
0110	Backup memory data error	EEPROM (Control PWB)
0120	MAC address data error For data in which the MAC address is invalid.	EEPROM (Control PWB)
0130	Backup memory read/write error (main NAMD)	Flash memory (Control PWB)
0140	Backup memory data error (main NAND)	Flash memory (Control PWB)
0150	Backup memory read/write error (control PWB) No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.	EEPROM (Control PWB)
0160	Backup memory data error (control PWB) Reading data from EEPROM is abnormal.	EEPROM
0170	Billing counting error The values on the main circuit PWB and on the engine do not match for any of charging counter, life counter, and scanner counter.	EEPROM. Control PWB
0180	Machine number mismatch Machine number of control does not match.	Data damage of EEPROM.
0190	Backup memory device error (control PWB)	Control PWB
0080	Image processing error JAM010X is detected twice.	Control PWB.
0800	Image processing error JAM010X is detected twice.	Control PWB.
0830	FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.	FAX software. FAX control PWB.
0420	Paper feeder communication error Communication error between control PWB and optional paper feeder.	Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF mainPWB.
0830	FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.	Defective fax software. Defective FAX control PWB.
0840	Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	Defective control PWB. The battery is disconnected from the control PWB.
0870	FAX control PWB to control PWB high capacity data transfer problem High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.	Improper installation FAX control PWB. Defective FAX control PWB or control PWB.
0920	Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.	Defective FAX control PWB.
0970	24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second.	Connect right PWB. Control PWB
1010	Lift motor error (50/60 ppm model only) After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the lift motor. Lift motor. Connect right PWB. Control PWB.
1020	PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1030	PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.	Dottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1040	PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1050	PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.	Bottom plate elevation mechanism in the cassette. Connector cable or poor contact in the connector. Drive transmission system of the PF lift motor. PF lift motor. PF main PWB.
1800	Paper feeder 1 communication error A communication error is detected 10 times in succession.	Paper feeder. Connector cable or poor contact in the connector. PF main PWB. Control PWB.
1810	Paper feeder 2 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB.
1820	Paper feeder 3 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB
1830	Paper feeder 4 communication error A communication error from paper feeder is detected 10 times in succession.	Paper feeder. PF main PWB. Control PWB
1900	Paper feeder 1 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1910	Paper feeder 2 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1920	Paper feeder 3 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
1930	Paper feeder 4 EEPROM error When writing the data, read and write data does not match 4 times in succession.	PF main PWB (EEPROM)
2000	Main motor startup error Main motor is not stabilized within 2 s since the motor is activated.	Main motor. Connect right PWB. Control PWB
2010	Main motor steady-state error After main motor is stabilized, the ready signal is not ready for 2 s continuously.	Main motor. Connect right PWB. Control PWB.
2200	Drum motor drive error (50/60 ppm model only) The drum motor is not stabilized within 2 s after driving starts.	Connector cable or poor contact in the connector. Drive transmission system of the drum motor. Drum motor. Connect right PWB. Control PWB.
2210	Drum motor steady-state error (50/60 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.	Connector cable or poor contact in the connector. Drive transmission system of the drum motor. Drum motor. Connect right PWB. Control PWB.
2330	Envelope motor error (Over-current) (50/60 ppm model only) The over-current detection signal of the motor is detected continuously twenty times.	Connector cable or poor contact in the connector. Drive transmission system of the envelope motor. Envelope motor. Connect left PWB. Control PWB.
2340	Envelope motor error (Timeout) (50/60 ppm model only) The position detection sensor is not detected continuously for 30 s.	Connector cable or poor contact in the connector. Drive transmission system of the envelope motor. Envelope motor. Connect left PWB. Control PWB.
2600	PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. DPF drive motor. DPF main PWB.
2610	PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
2620	PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
2630	PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s	Connector cable or poor contact in the connector. Drive transmission system of the PF drive motor. PF drive motor. PF main PWB.
3100	Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor.	Image scanner motor. Home position sensor. CCD PWB. Control PWB.
3200	Exposure lamp error When a lamp is made to turn on one side at a time, the white standard data at the time of an initial is lower than a rated value.	LED PWB. CCD PWB. Control PWB.
3500	Communication error between scanner and ASIC An error code is detected.	CCD PWB. Control PWB.
4000	Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 20 s continuously.	Polygon motor (LSU). Control PWB.
4200	BD steady-state error The BD signal is not detected.	PD PWB (LSU). Control PWB.
5100	Chager current error When the current value measured at the time of potential adjustment is less than 20 mcA. The error of the charge current before toner installation. The error of the charge current before printing.	Connector cable or poor contact in the connector. High voltage PWB. Control PWB.
6000	Broken fuser heater wire (Center) (50/60 ppm model) Fuser thermistor 2 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start. (40 ppm model) Fuser thermistor 1 detects a temperature less than 100°C/ 212°F continuously for 30 s after a warm-up start.	Fuser unit. Fuser thermistor connect PWB. Control PWB. Power source PWB. Fuser heater.
6020	Abnormally high fuser thermistor 2 temperature (Center) (50/60 ppm model only) Fuser thermistor 2 detects a temperature higher than 235°C/455°F. In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.	Fuser unit. Fuser thermistor connect PWB. Control PWB.
6030	Broken fuser thermistor 2 wire (Center) (50/60 ppm model only) Input from fuser thermistor 2 is 1019 or more (A/D value) continuously for 4 s.	Fuser unit. Fuser thermistor connect PWB. Control PWB. Fuser thermistor 2. Fuser thermostat (triggered). Power source PWB
6120	Abnormally high fuser thermistor 1 temperature (50/60 ppm model) The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less. (40 ppm model) The detection temperature of fuser thermistor 1 is higher than 250°C/482°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 170°C/338°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.	Connector pin. Triac. Fuser thermistor. Contrl PWB.
6130	Broken fuser thermistor 1 wire (50/60 ppm model only) A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.	Connector cable or poor contact in the connector. Connector pin. Triac. Fuser thermistor. Fuser thermistor connect PWB. Control PWB.
6400	Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 2 s.	Fuser unit. Power source PWB. Connect right PWB. Control PWB.
7000	Toner motor error During driving the toner motor, an over-current detection signal is detected at intervals of 10 ms as for 300 accumulation.	Connector cable or poor contact in the connector. Drum unit. Connect left PWB. Control PWB.
7100	Toner sensor error Sensor output value of 930 or more continuously for 5 s.	Toner sensor. Toner motor. Connect left PWB. Control PWB.
7400	Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.	Connector cable or poor contact in the connector. Toner sensor. Connect left PWB. Control PWB.
7410	Drum unit type mismatch error The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.	Connector cable or poor contact in the connector. Toner sensor. Connect left PWB. Control PWB.
7800	Broken temperature sensor wire Input from temperature sensor is 1019 or more continuously for 160 ms. Input from temperature sensor is 930 or more continuously for 5 s.	Temperature sensor. Control PWB.
7810	Short-circuited temperature sensor wire Input from temperature sensor is 31 or less continuously for 5 s.	Temperature sensor. Control PWB.
7900	Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.	DR PWB. Connect left PWB. Control PWB.
F000	Communication error between Control PWB and Operation PWB	Control PWB. Operation PWB.
F010	Control PWB checksum error	Control PWB.
F020	Control PWB RAM check sum error	Main memory (RAM).
F040	Communication error between Controller and Print engine	Control PWB.
F041	Communication error between Controller and Scan engine	Control PWB.
F050	Print engine ROM checksum error	Control PWB.
F051	Scan engine ROM checksum error	Control PWB.

Источник

Кто сейчас на форуме

KYOCERA P3145DN код ошибки 7410:0035148

KYOCERA P3145DN код ошибки 7410:0035148

Кто сейчас на форуме

KYOCERA P3145DN код ошибки 7410:0035148

KYOCERA P3145DN код ошибки 7410:0035148

Не пропустите эти материалы по теме: