Ошибка 005 на телевизоре панасоник

Panasonic is one of the top TV manufacturers in the world, offering not just home entertainment systems but inflight entertainment systems as well. Founded 104 years ago, this Japanese multinational corporation was once a light bulb socket manufacturer. Spending its wings Panasonic took a leap of faith and is not one of the leading names in the market.

Apart from catering to a wide range of industries, They offer a wide range of selections when it comes to televisions, ensuring you get one based on your unique requirements. Offering you top-of-the-line choices that fit in your home or workspace in a way that enhances your overall experience.

Panasonic might be one of the oldest manufacturers in the world, but its TVs are as open to errors as any other company. To help you out we have listed down some of the most common error codes for Panasonic TVs. Start by noting down the error code, and match it using the list below. Once you have the error code you can easily work your way to the fix.

2010 Panasonic 3D Plasma TV (13th Generation). Power LED Error Code Definition.

The following table identifies the areas where a problem is suspected according to the number of times that the POWER LED blinks.

SOS Detect (Shutdown)

When an abnormality occurs in the unit, the “SOS Detect” circuit is triggered and the TV shuts down. The power LED on the front panel will flash a pattern indicating the circuit that has failed.

Cautions: If the power LED continues to blink even after the TV is unplugged, press and hold the power switch on the TV for a few seconds until the LED turns off. Some steps require removal of connectors and sometimes PC boards removal. Do not allow the TV to run for more than 30 seconds while connectors or boards are disconnected.

SOS Detect Circuit

Protection circuits are incorporated in the unit to prevent the failure of a single circuit or component from creating catastrophic damage. A shutdown condition occurs when a there is an over voltage, a short or a drop in any of the voltage lines. Also when the fans are drawing more current than normal the shutdown circuit is triggered. Normally the CPU of the D board and the CPU of the A board detect when a shutdown condition has been triggered. When an abnormality has occurred, the unit protection circuit operates and the TV is reset to the stand-by mode. At this time, the defective block can be identified by the number of blinks of the POWER LED on the front of the unit.

IC9003 of the D board detects conditions that make the power LED blinks 2, 3, 4, 5, 6, 7, 8, or 9 times. IC 1100 on the A board detects conditions that make the power LED blinks 10, 11, and 12 times.

1 Blink SOS: Communication error between System CPU (IC1100) and Panel CPU (IC9003).

2 Blinks SOS: Pin 62 of the CPU IC9003 monitors the 15V line. During normal operation, the pin 62 is high. If the 15V line is missing or shorted, a low is provided to pin 62. As a result, the unit shuts down and the power LED blinks 2 times.

3 Blinks SOS: IC9802 is a 3.3V regulator located on the D board. Its output is monitored by IC9003. If the 3.3V is not present at pin 61, the MPU shuts down the unit. The power LED blinks 3 times.

4 Blinks SOS: When an over voltage condition of the voltage lines from the power supply occurs, pin 16 of IC701 goes high. This high is provided to pin 67 of IC9003 of the D board triggering the “POWER SOS” circuit. When this happens, the TV shuts down and the power LED blinks 4 times.

5 Blinks SOS: Pin 60 of the CPU IC9003 monitors the 5V line. During normal operation, the pin 69 is high. If the 5V line is missing or shorted, a low is provided to pin 60. As a result, the unit shuts down and the power LED blinks 5 times.

6 Blinks SOS: Pin 65 of the CPU IC9003 monitors the status of the SC board. During normal operation, a low is applied to pin 65. If the SC board becomes defective, a high is provided to pin 65. As a result, the unit shuts down and the power LED blinks 6 times.

7 Blinks SOS: Pin 68 of the CPU IC9003 monitors the status of the SC, SU, SD board. During normal operation, a low is applied to pin 68. If the SC, SU, or SD board becomes defective, a high is provided to pin 68. As a result, the unit shuts down and the power LED blinks 7 times.

8 Blinks SOS: Pin 66 of the MPU IC9003 monitors the status of the SS board. During normal operation, pin 7 of connector SS33 outputs a low to pin 66. If the SS board becomes defective, a high is provided to pin 66. As a result, the unit shuts down and the power LED blinks 8 times. Another SOS Detect circuit in the Sustain board monitors for physical connection between the SS board and the panel. If any of the flex-cables from the panel is not connected or is not properly seated, a high is provided to pin 66 of the CPU in the D board. When this happened, the TV shuts down and the power LED blinks 8 times.

9 Blinks SOS: Pins 85 and 86 of the MPU IC9003 monitor the status of IC9300 and IC9400. During normal operation, pin 85 and pin 86 are low. A malfunction of IC9300 or IC9400 triggers a shutdown and the power LED blinks 9 times.

11 Blinks Error Code Explanation: The internal temperature of the unit is monitored by the digital temperature sensor (IC9002). Variations in temperature are sensed by the IC and reported to the D board MPU (IC9003) via the SDA02 bus line. IC9003 then conveys the information to the A board MPU (IC1100) via the SDA1 bus line. Fan speed is controlled by IC9003.

The ventilation fans are monitored to be sure they are operating properly. If one of the fans opens or increases resistance, the resulting current change is applied to pin 61 of the main CPU (IC1100).

The fan drive circuit is located on the A board. To control the speed of the fan, a control voltage from the microprocessor(IC1100) is applied to IC5740. If any of the fans is removed or becomes defective, a high is output at the corresponding pin (pin 3, 9, or 12) of the fan connector (A30) to forward bias the inline diode. The DC output of the diode is provided to pin 61 of IC1100 to trigger the SOS condition.

12 Blinks Error Code (Sound):

The transistor Q2300 monitors the speaker amplifiers ICs (IC2301 and IC2302). Pin 3 of both ICs is normally high. If any of these ICs or one of the speakers develops a short circuit, pin 3 goes low causing Q2300 to go into conduction and output a low to the base of Q2300. As a result, Q2300 comes on and outputs a high to pin 27 of the System CPU (IC1100) on the A board.

Panasonic TV Troubleshooting

Before requesting service or assistance, please follow these simple guides to resolve the problem. If an error message appears, follow the message’s instructions. If the problem still persists, please contact your local Panasonic dealer for assistance

Care and Cleaning

First, unplug the Power cord plug from the wall outlet.

Display panel: The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lintfree cloth.

• If the surface is particularly dirty, after cleaning up the dust, soak a soft, lint-free cloth in diluted, mild liquid dish soap (1 part mild liquid dish soap diluted by 100 times the amount of water), and then wring the cloth to remove excess liquid. Use this cloth to wipe the surface of the display panel, then wipe it evenly with a dry cloth of the same type until the surface is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with volatile substances such as insect sprays, solvents, and thinner; otherwise, the quality of the surface may be adversely affected.

Cabinet: If the cabinet becomes dirty, wipe it with a soft, dry cloth.

• If the cabinet is particularly dirty, soak the cloth in diluted, mild liquid dish soap and then wring the cloth dry. Use this cloth to wipe the cabinet and then wipe it dry with a dry cloth.
• Do not allow any mild liquid dish soap to come into direct contact with the surface of the Plasma TV. If water droplets get inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents, and thinner; otherwise, the quality of the cabinet surface may be adversely affected or the coating may peel off.
• Do not let articles made from rubber or PVC be in contact with the TV for long periods of time.

Pedestal:

• Cleaning. Wipe the surfaces with a soft, dry cloth. If the unit is particularly dirty, clean it using a cloth soaked with water to which a small amount of mild liquid dish soap has been added and then wipe with a dry cloth. Do not use products such as solvents, thinner, or household wax for cleaning, as they can damage the surface coating. (If using a chemically-treated cloth, follow the instructions supplied with the cloth.)
• Do not attach sticky tape or labels, as they can make the surface of the pedestal dirty. Do not allow long-term contact with rubber, vinyl products, or the like. (Doing so will cause deterioration.)

Power cord plug: Wipe the plug with a dry cloth at regular intervals. (Moisture and dust can lead to fire or electrical shock.)

Panasonic TV Manual PDF

В любой момент телевизор марки Panasonic может начать работать с неисправностями или перестать работать полностью. Такое случается очень частно и мы постоянно устраняем такие неисправности. Так же все модели телевизоров оснащены световым индикаторам для опредления поломки с помощью количества мигания. Любую техническую проблему можно устранить самостоятельно, если правильно расшифровать код ошибки. 

→ Совет от мастера. Телевизор это сложное техническое устройство и лучше вызывать мастера по ремонту телевизора на дом в удобное вам время из РБТ Сервис. Но, если вы хотите починить сами, тогда читаем ниже. 

Чаще всего технические проблемы бывают после перепада напряжени сети, механических ударов или сами по себе выходят из строя. Даже если у вашего телевизора исправен корпус и кажется все идеально он все равно может не работать.

Основные неисправности телевизора Panasonic:

• Телевизор перестал включаться.
• Неисправна подсветка.
• Не работает звук.
• Писк во время работы телевизора.

Как устранить такие проблемы?

Если у вас загорелся индикатор, тогда нужно считать количество морганий и написать нам и мы подскажем, что за ошибка у вашей техники. Ниже мы опищем самые простые варианты которые вы сможете устранить сами.

1. Если ваш телевизор перестала включаться например с пульта, тогда нужно попробывать включить его в ручном режиме, проверить шнур питания и розетку. Так же возможно у вас сгорел предохранитель в телезвиоре который нужно заменить. Если у вас проблема на плате управления, тогда вам нужно будет разобрать корпус и найти сгоревшие радиодетали и заменить их на схеме. Так же первым делом нужно проверить блок питания так как на нем расположены основные комплектующие.
2. Когда телевизор перестал показывать, тогда вероятно у вас вышла из строя подсветка. Как проверить, что проблема в ней? У вас есть звук, но нет картинки? Возьмите фонарик и вблизи посветите на него и тогда вы увидите картинку. Для замены подсветки вам нужно будет разобрать корпус телевизора, дальше необходимо снять матрицу и заменить не рабочую подсветку чатями или планки целиком. 
3. Не работает звук. Вам нужно так же разобрать корпус и проверить все динамики. Заменить не рабочие детали на новые.
4. Появился писк у телевизора во время просмотра. Вероятно из строя выходят конденсаторы или транзисторы которые нужно заменить на новые. Для этого вам так же надо разобрать корпус и добраться до схем.
5. Если у вас включается телевизор, но видно трещины на экране, тогда у вас разбита матрица. Ее можно заменить, но это не целесобразный ремонт. Необходимо приготовиться к покупке нового. 

Ну вот мы и закончили  кодами ошибок для телевизоров lg и теперь вы можете самостоятельно их устранить не прибегая к помощи мастера. Всем желаю хорошего дня! С любовью ваш РБТ Сервис.